Nissan Cube. Instruction — part 1035
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
WT-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000009949864
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009949865
1.
CHECK TIRE PRESSURE
Check the internal pressure of all wheels. Refer to
.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
GENT KEY : Removal and Installation"
(With intelligent key system),
GENT KEY : Removal and Installation"
(Without intelligent key system).
NO
>> After adjusting the tire pressure, GO TO 2.
2.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Check and adjust the tire pressure for all wheels. Refer to
.
2.
Perform tire pressure sensor ID registration for all wheels. Refer to
.
3.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
4.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
5.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 15 minutes, use CONSULT “DATA MONITOR” to display the tire pres-
sure for all wheels.
6.
Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm
2
, 63.60 Psi).
Is the inspection 438.60 kPa (4.47 kg/cm
2
, 63.60 Psi)?
YES
>> Replace tire pressure sensor the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm
2
, 63.60 Psi) dis-
played. Refer to
WT-48, "WITH INTELLIGENT KEY : Removal and Installation"
(With intelligent
key system),
WT-51, "WITHOUT INTELLIGENT KEY : Removal and Installation"
(Without intelli-
gent key system).
NO
>> GO TO 1.
DTC
Display item
Malfunction detected condition
Possible case
C1716
[PRESSDATA ERR] FL
Malfunction in the tire pressure data from the front left
wheel tire pressure sensor.
• Excessive tire pressure
• ID registration is not fin-
ished
• Tire pressure sensor mal-
function
C1717
[PRESSDATA ERR] FR
Malfunction in the tire pressure data from the front right
wheel tire pressure sensor.
C1718
[PRESSDATA ERR] RR
Malfunction in the tire pressure data from the rear right
wheel tire pressure sensor.
C1719
[PRESSDATA ERR] RL
Malfunction in the tire pressure data from the rear left wheel
tire pressure sensor.
WT-32
< DTC/CIRCUIT DIAGNOSIS >
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
Special Repair Requirement
INFOID:0000000009949866
1.
CHECK TIRE PRESSURE
Check all tires for tire pressures. Refer to
.
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
.
>> END
C1729 VEHICLE SPEED SIGNAL
WT-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1729 VEHICLE SPEED SIGNAL
Description
INFOID:0000000009949867
BCM detects no vehicle speed signal.
DTC Logic
INFOID:0000000009949868
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009949869
1.
PERFORM COMBINATION METER SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” of “METER/M&A”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK INFORMATION
With CONSULT
1.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
2.
Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to
(With intelligent key system),
(Without intelligent key system).
Is the inspection result normal?
YES
>> Check pin terminal and connection of each harness connector for malfunctioning conditions.
NO
>> Replace BCM. Refer to
(With intelligent key system),
(Without intelligent key system).
Special Repair Requirement
INFOID:0000000009949870
1.
CHECK TIRE PRESSURE
Check all tires for tire pressures. Refer to
.
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
.
>> END
DTC
Display item
Malfunction detected condition
Possible case
C1729
VHCL SPEED SIG ERR
Vehicle speed signal not detected.
• CAN communication error
• Combination meter malfunction
WT-34
< DTC/CIRCUIT DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP
LOW TIRE PRESSURE WARNING LAMP
Component Function Check
INFOID:0000000009949871
1.
CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP
Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000009949872
1.
POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
(With intelligent key system),
(Without intelligent key system).
NO
>> GO TO 3.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
MWI-39, "COMBINATION METER : Diagnosis Procedure"
.
NO
>> Replace the BCM. Refer to
(With intelligent key system),
(Without intelligent key system).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст