Nissan Cube. Instruction — part 885

B1050, B1055 DRIVER AIR BAG MODULE

SRC-57

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

4.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to

SR-11, "Exploded View"

.

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to

SR-26, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to

SRC-56, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to

SR-11, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to

SRC-56, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Driver air bag module

Combination switch (spiral cable)

Continuity

Connector

Terminal

Connector

Terminal

M350

10

M32

28

Existed

11

30

M351

12

29

9

30

Driver side air bag module

Ground

Continuity

Connector

Terminal

M350

10

Not existed

11

M351

12

9

SRC-58

< DTC/CIRCUIT DIAGNOSIS >

B1051, B1056 DRIVER AIR BAG MODULE

B1051, B1056 DRIVER AIR BAG MODULE

Description

INFOID:0000000009946145

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946146

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-58, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946147

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module connector and combination switch (spiral cable) connector.

3.

Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1051
B1056

DRIVER AIRBAG
MODULE
[GND-SHORT]

Driver air bag module circuit is shorted to ground
(including the spiral cable)

• Disconnection of wiring harness and short
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

B1051, B1056 DRIVER AIR BAG MODULE

SRC-59

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

4.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to

SR-11, "Exploded View"

.

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to

SR-26, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to

SRC-58, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to

SR-11, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to

SRC-58, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Driver air bag module

Combination switch (spiral cable)

Continuity

Connector

Terminal

Connector

Terminal

M350

10

M32

28

Existed

11

30

M351

12

29

9

30

Driver side air bag module

Ground

Continuity

Connector

Terminal

M350

10

Not existed

11

M351

12

9

SRC-60

< DTC/CIRCUIT DIAGNOSIS >

B1052, B1057 DRIVER AIR BAG MODULE

B1052, B1057 DRIVER AIR BAG MODULE

Description

INFOID:0000000009946148

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946149

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-60, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946150

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module connector and combination switch (spiral cable) connector.

3.

Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1052
B1057

DRIVER AIRBAG
MODULE
[SHORT]

Driver air bag module circuit are shorted to each
other
(including the spiral cable)

• Disconnection of wiring harness and short
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit