Nissan Cube. Instruction — part 67
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-117
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
WORK SUPPORT
ACTIVE TEST
RETAIND PWR
RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000010249177
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
KEYLESS UNLOCK
Indicates [ON/OFF] condition of unlock signal from keyfob.
TRUNK OPNR SW
NOTE:
The item is indicated, but not monitored.
TRNK OPNR MNTR
NOTE:
The item is indicated, but not monitored.
HOOD SW
NOTE:
The item is indicated, but not monitored.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW
Indicates [ON/OFF] condition of back door switch.
KEY CYL LK-SW
Indicates [ON/OFF] condition of door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of door key cylinder switch.
CDL LOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
TRANSPONDER
Indicates key ID verification results by [ON/OFF].
INTELLI KEY
NOTE:
The item is indicated, but not monitored.
LOCK STATUS
NOTE:
The item is indicated, but not monitored.
AUTO RELOCK
NOTE:
The item is indicated, but not monitored.
Monitor Item
Condition
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching
“CLEAR” on CONSULT screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on
CONSULT screen is touched.
HEADLAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5
seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.
BCS-118
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)
INFOID:0000000009949782
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function
INFOID:0000000010249126
FUNCTION
The diagnosis functions (main functions) include the following: “WORK SUPPORT”, “SELF DIAGNOSTIC
RESULT”, “DATA MONITOR” and “ACTIVE TEST”.
WORK SUPPORT MODE
SELF-DIAG RESULTS MODE
DATA MONITOR MODE
Screen of data monitor mode is displayed.
NOTE:
• When malfunction is detected, CONSULT perform REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
• The following table includes information(items)inapplicable to this vehicle. For information(items)applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Description
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Monitor item [UNIT]
Description
OIL PRESS SW
[Off/On]
Displays the status of oil pressure switch received from IPDM E/R with CAN communication.
BRAKE SW
[Off/On]
Displays the switch status input from stop lamp switch.
Test item
Operation
Description
OIL PRESSURE SW
On
Transmits the oil pressure switch signal with CAN communication to illuminate the oil
pressure warning lamp in the combination meter.
Off
Stops the oil pressure switch signal transmission.
Diagnostic test mode
Function
Work support
In this mode, it is possible to make quick and accurate adjustments by following the instruc-
tions on the CONSULT display.
Self diagnostic result
Receives self-diagnosis results from the BCM, and indicates DTCs and the number of mal-
functions.
Data monitor
Receives input/output signals from the BCM and indicates and stores them to facilitate locating
the causes of malfunctions.
Active test
Transmits command to the BCM to change output signals and check operation of output sys-
tem.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-119
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT.
ACTIVE TEST MODE
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT.
TEST ITEM LIST
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)
INFOID:0000000010249176
ACTIVE TEST
Monitor item (Unit)
Remark
AIR PRESS FL (kPa), (kg/cm
2
), (Psi)
Air pressure of tires
AIR PRESS FR (kPa), (kg/cm
2
), (Psi)
AIR PRESS RR (kPa), (kg/cm
2
), (Psi)
AIR PRESS RL (kPa), (kg/cm
2
), (Psi)
ID REGST FL1
ID is registered: Done
ID is not registered: Yet
ID REGST FR1
ID REGST RR1
ID REGST RL1
WARNING LAMP
Low tire pressure warning lamp ON: On
Low tire pressure warning lamp OFF: Off
BUZZER
Combination meter buzzer ON: On
Combination meter buzzer OFF: Off
Test item
Content
WARNING LAMP
This test is able to check to check that the low tire pressure warning lamp turns on.
ID REGIST WARNING
This test is able to check to check that the buzzer sounds or the low tire pressure warning lamp
turns on.
RUN FLAT TIRE W/L
NOTE:
This item is displayed, but cannot be use this item.
FLASHER
This test is able to check to check that each turn signal lamp turns on.
HORN
This test is able to check to check that the horn sounds.
Test item
Description
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON”
on CONSULT screen touched.
HEAD LAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated af-
ter “ON” on CONSULT screen touched.
BCS-120
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
U1000 CAN COMM
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
Description
INFOID:0000000009949785
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to
LAN-22, "CAN Communication Signal Chart"
DTC Logic
INFOID:0000000009949786
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000009949787
1.
PERFORM SELF DIAGNOSTIC
1.
Turn ignition switch ON and wait for 2 seconds or more.
2.
Check “Self Diagnostic Result” of BCM.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Refer to
LAN-13, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
DTC
DTC Detection Condition
Possible cause
U1000: CAN COMM
When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more.
CAN communication system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст