Nissan Cube. Instruction — part 844
DIAGNOSIS SYSTEM (BCM)
SEC-187
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ACTIVE TEST
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)
INFOID:0000000009950251
ACTIVE TEST
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching
“CLEAR” on CONSULT screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on
CONSULT screen is touched.
HEADLAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5
seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.
Test item
Description
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON”
on CONSULT screen touched.
HEAD LAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated af-
ter “ON” on CONSULT screen touched.
SEC-188
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (IPDM E/R)
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT Function (IPDM E/R)
INFOID:0000000010251892
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the shift position (CVT models) judged by IPDM E/R.
ST RLY-REQ
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN
communication.
DTRL REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
OIL P SW
[Open/Close]
Displays the status of the oil pressure switch judged by IPDM E/R.
HOOD SW
[Off/On]
NOTE:
The item is indicated, but not monitored.
DIAGNOSIS SYSTEM (IPDM E/R)
SEC-189
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ACTIVE TEST
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder signal received from BCM via CAN com-
munication.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Operates the cooling fan relay (LO operation).
3
Operates the cooling fan relay (HI operation).
4
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
ond intervals.
Fog
Operates the front fog lamp relay.
SEC-190
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
P1610 LOCK MODE
DTC/CIRCUIT DIAGNOSIS
P1610 LOCK MODE
Description
INFOID:0000000009950253
ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times
or more while communication between ECM and BCM is not normal, and when engine start operation is per-
formed 5 times or more by unregistered ignition key.
DTC Logic
INFOID:0000000009950254
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnosis result” with CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-190, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009950255
1.
CHECK ENGINE START FUNCTION
1.
Perform the check for DTC except DTC P1610.
2.
Use CONSULT to erase DTC after fixing.
3.
Turn ignition switch OFF.
4.
Turn ignition switch ON when registered ignition key is inserted into key cylinder and wait for 5 seconds.
5.
Turn the ignition switch OFF and wait 5 seconds.
6.
Repeat steps 4 and 5 twice (a total of 3 times).
7.
Check that engine can start when registered ignition key is inserted into key cylinder.
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1610
LOCK MODE
When ECM detects any of the following 2 states
• Ignition switch ON 5 times or more during communication between
ECM and BCM is malfunctioning
• Ignition switch ON by unregistered ignition key 5 times or more
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст