Nissan Cube. Instruction — part 572
HAC-126
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
INTAKE SENSOR
INTAKE SENSOR
Exploded View
INFOID:0000000009951041
HA-42, "Exploded View (Automatic Air Conditioner)"
.
Removal and Installation
INFOID:0000000009951042
REMOVAL
1.
Remove the evaporator assembly. Refer to
HA-42, "Exploded View (Automatic Air Conditioner)"
.
2.
Remove the intake sensor from evaporator.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply the compressor oil to them when installing.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Never rotate the bracket insertion part when removing and installing the intake sensor.
• Check for leakages when recharging refrigerant. Refer to
REFRIGERANT PRESSURE SENSOR
HAC-127
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000009951043
Removal and Installation
INFOID:0000000009951044
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
26, "Perform Lubricant Return Operation"
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2.
Clean refrigerant pressure sensor and its surrounding area, and then remove dust and rust from refriger-
ant pressure sensor.
CAUTION:
Be sure to clean carefully.
3.
Disconnect refrigerant pressure sensor connector.
1.
Condenser
2.
Refrigerant pressure sensor
3.
O-ring
4.
Grommet
5.
Condenser seal
6.
Bracket
7.
O-ring
8.
Liquid tank bracket
9.
Liquid tank
Refer to
JPIIA1552GB
HAC-128
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
REFRIGERANT PRESSURE SENSOR
4.
Use a adjustable wrench (A) or other tool to hold the refrigerant
pressure sensor mounting block, and then remove the refriger-
ant pressure sensor (2) from the condenser (1).
CAUTION:
• Be careful not to damage liquid tank.
• Be careful not to damage core surface of condenser.
• Cap or wrap the joint of the condenser and liquid tank
with suitable material such as vinyl tape to avoid the entry
of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant. Refer to
JPIIA1708ZZ
POWER TRANSISTOR
HAC-129
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
POWER TRANSISTOR
Exploded View
INFOID:0000000009951045
Removal and Installation
INFOID:0000000009951046
REMOVAL
1.
Remove instrument panel assembly. Refer to
.
2.
Remove cowl top extension. Refer to
3.
Remove instrument stay.
4.
Remove mounting bolts (A), and then move steering member (1) to a position where it dose not inhibit
work.
5.
Disconnect power transistor connector.
6.
Press flange holding hook (A), and then slide heater core to left-
ward.
7.
Remove power transistor (1) from the A/C unit assembly.
INSTALLATION
Installation is basically the reverse order of removal.
JPIIA1730ZZ
JPIIA1731ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст