Nissan Cube. Instruction — part 479
EXL-190
< PERIODIC MAINTENANCE >
FRONT FOG LAMP AIMING ADJUSTMENT
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
FRONT COMBINATION LAMP
EXL-191
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009945209
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009945210
REMOVAL
1.
Front combination lamp
A.
Air duct clip(only left)
JPLIA1726ZZ
1.
Parking(side marker) lamp bulb
2.
Parking(side marker)lamp bulb sock-
et
3.
Back cover
4.
Halogen bulb
5.
Front turn signal lamp bulb socket
6.
Front turn signal lamp bulb
7.
Headlamp housing assembly
8.
Retaining spring
JPLIA1807ZZ
EXL-192
< REMOVAL AND INSTALLATION >
FRONT COMBINATION LAMP
CAUTION:
Disconnect the battery negative terminal or the fuse.
1.
Remove front bumper fascia. Refer to
2.
Remove the harness clips (A)*.
*: When replace a left.
3.
Remove the air duct clip*.
*: When replace a left.
4.
Remove the headlamp mounting bolts.
5.
Pull out the headlamp assembly forward the vehicle.
6.
Disconnect the connector before removing the headlamp
assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000009945211
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1.
Disconnect the headlamp bulb connector.
2.
Remove the back cover.
3.
Remove the retaining spring lock. And remove the bulb from the headlamp housing assembly.
PARKING(FRONT SIDE MARKER) LAMP BULB
1.
Remove the fender protector. Refer to
EXT-21, "FENDER PROTECTOR : Exploded View"
vice area.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
Disassembly and Assembly
INFOID:0000000009945212
DISASSEMBLY
1.
Remove the back cover.
2.
Remove the retaining spring lock. And remove the bulb from the headlamp housing assembly.
3.
Rotate the parking(front side marker) lamp bulb socket counterclockwise and unlock it.
4.
Remove the bulb from the parking(front side marker) lamp bulb socket.
5.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6.
Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
JPLIA1727ZZ
FRONT COMBINATION LAMP
EXL-193
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст