Nissan Cube. Instruction — part 940

TM-16

< PREPARATION >

[6MT: RS6F94R]

PREPARATION

Drift
a: 45 mm (1.77 in) dia.
b: 39 mm (1.54 in) dia.

Installing differential side bearing inner race
(clutch housing side)

Drift
a: 52 mm (2.05 in) dia.
b: 45 mm (1.77 in) dia.

Installing differential side bearing inner race
(transaxle case side)

Puller

• Removing differential side bearing inner

race (clutch housing side)

• Removing differential side bearing inner

race (transaxle case side)

Puller

• Removing differential side bearing inner

race (clutch housing side)

• Removing differential side bearing inner

race (transaxle case side)

• Removing input shaft rear bearing
• Removing input shaft front bearing
• Removing mainshaft rear bearing inner race
• Removing 6th main gear
• Removing 4th main gear
• Removing 5th main gear
• Removing 1st main gear
• Removing 1st-2nd synchronizer hub as-

sembly

• Removing 2nd main gear
• Removing 3rd main gear
• Removing mainshaft front bearing inner

race

Remover

• Removing bushing
• Removing mainshaft rear bearing outer

race

Power tool

Loosening bolts and nuts

Tool name

Description

S-NT474

S-NT474

NT077

ZZB0823D

S-NT134

PBIC0190E

GEAR OIL

TM-17

< PERIODIC MAINTENANCE >

[6MT: RS6F94R]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

PERIODIC MAINTENANCE

GEAR OIL

Inspection

INFOID:0000000009948866

OIL LEAKAGE

Make sure that gear oil is not leaking from transaxle or around it.

OIL LEVEL

1.

Remove filler plug (1) and gasket from transaxle case.

2.

Check the oil level from filler plug mounting hole as shown in the
figure.

CAUTION:

Never start engine while checking oil level.

3.

Set a gasket on filler plug and then install it to transaxle case.

CAUTION:

Never reuse gasket.

4.

Tighten filler plug to the specified torque. Refer to

TM-27,

"Exploded View"

.

Draining

INFOID:0000000009948867

1.

Start engine and let it run to warm up transaxle.

2.

Stop engine. Remove drain plug (1) and gasket, using a socket
[Commercial service tool] and then drain gear oil.

3.

Set a gasket on drain plug and install it to clutch housing, using
a socket [Commercial service tool].

CAUTION:

Never reuse gasket.

4.

Tighten drain plug to the specified torque. Refer to

TM-27,

"Exploded View"

.

Refilling

INFOID:0000000009948868

1.

Remove filler plug (1) and gasket from transaxle case.

2.

Fill with new gear oil until oil level reaches the specified limit at
filler plug mounting hole as shown in the figure.

3.

After refilling gear oil, check the oil level. Refer to

TM-17,

"Inspection"

.

4.

Set a gasket on filler plug and then install it to transaxle case.

CAUTION:

Never reuse gasket.

5.

Tighten filler plug to the specified torque. Refer to

TM-27, "Exploded View"

.

SCIA7623E

SCIA7622E

Oil grade and
viscosity

: Refer to

MA-10, "Fluids and Lubricants"

.

Oil capacity

: Refer to

TM-63, "General Specification"

.

SCIA7623E

TM-18

< REMOVAL AND INSTALLATION >

[6MT: RS6F94R]

SIDE OIL SEAL

REMOVAL AND INSTALLATION

SIDE OIL SEAL

Removal and Installation

INFOID:0000000009948869

REMOVAL

1.

Remove front drive shafts. Refer to

FAX-16, "LEFT SIDE : Removal and Installation"

(LH) and

FAX-17,

"RIGHT SIDE : Removal and Installation"

(RH).

2.

Remove differential side oil seals (1) from clutch housing and
transaxle case, using a suitable tool.

CAUTION:

Never damage transaxle case and clutch housing.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Install differential side oil seals (1) to clutch housing and transaxle

case, using the drift [Stamping number: B.vi 1666-B] of the drift set
[SST: KV32500QAA ( - )].

CAUTION:

• Never incline differential side oil seal.
• Never damage clutch housing and transaxle case.

Inspection

INFOID:0000000009948870

INSPECTION AFTER INSTALLATION

Check the oil leakage and the oil level. Refer to

TM-17, "Inspection"

.

SCIA7625E

A

: Transaxle case side

B

: Clutch housing side

Dimension “L

1

”

: 1.2 – 1.8 mm (0.047 – 0.071 in)

Dimension “L

2

”

: 2.7 – 3.3 mm (0.106 – 0.130 in)

JPDIC0454ZZ

CONTROL LINKAGE

TM-19

< REMOVAL AND INSTALLATION >

[6MT: RS6F94R]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

CONTROL LINKAGE

Exploded View

INFOID:0000000009948871

Removal and Installation

INFOID:0000000009948872

REMOVAL

1.

Pull the shifter lever knob upward to remove.

2.

Remove center console assembly. Refer to

IP-23, "Removal and Installation"

.

3.

Remove harness clips.

4.

Shift the shifter lever in the neutral position.

5.

Remove mounting bolts of the M/T shift selector.

6.

Remove air duct (inlet). Refer to

EM-24, "Removal and Installation"

.

7.

Remove battery. Refer to

PG-82, "Removal and Installation"

.

1.

Bracket

2.

Shifter cable

3.

Shifter lever A

4.

Selector lever

5.

Selector cable

6.

Tapping bolt

7.

Cable mounting bracket

8.

Lock plate

9.

M/T shift selector

10. Shifter lever

11.

Shifter lever knob

Refer to

GI-4, "Components"

for the symbols in the figure.

JPDIC0649GB