Nissan Cube. Instruction — part 122
REPLACEMENT OPERATIONS
BRM-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
REPLACEMENT OPERATIONS
Description
INFOID:0000000009949335
• This section is prepared for technicians who have attained a high level of skill and experience in repairing
collision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
• Technicians are also encouraged to read the Body Repair Instruction (Fundamentals) in order to ensure that the
original functions and quality of the vehicle are maintained. The Body Repair Instruction (Fundamentals) con-
tains additional information, including cautions and warnings, that are not including in this instruction. Techni-
cians should refer to both manuals to ensure proper repair.
• Please note that this information is prepared for worldwide usage, and as such, certain procedures might not
apply in some regions or countries.
The symbols used in this section for welding operations are shown below.
Symbol marks
Description
2-spot welds
3-spot welds
MIG plug weld
For 3 panels plug weld method
MIG seam weld / Point weld
JSKIA0049ZZ
JSKIA0053ZZ
JSKIA0050ZZ
JSKIA0051ZZ
JSKIA0054ZZ
JSKIA0055ZZ
JSKIA0052ZZ
JSKIA0056ZZ
BRM-22
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
• Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is at
position A due to the construction of the vehicle.
• Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm (2.36 in) above the inner front pillar cut
position.
• Prepare a cutting jig to make outer pillar easier to cut. Also, this will
permit the service part to be accurately cut at the joint position.
• An example of cutting operation using a cutting jig is as per the fol-
lowing.
1.
Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar
2.
Align cutting line with notch on jig. Clamp jig to pillar.
3.
Cut outer pillar along groove of jig (at position A).
4.
Remove jig and cut remaining portions.
5.
Cut inner pillar at position B in same manner.
PIIA0150E
JSKIA0104GB
JSKIA0105GB
PIIA0153E
REPLACEMENT OPERATIONS
BRM-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Radiator Core Support
INFOID:0000000009949336
Hoodledge
INFOID:0000000009949337
Work after radiator core support is removed.
: Vehicle front
: Weld the parts onto the back of the component part.
Replacement parts
z
Side radiator core support (LH)
z
Side radiator core reinforcement
(LH)
z
Hoodledge connector (LH)
JSKIA1150ZZ
BRM-24
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Remove the front side closing plate reinforcement (reusable) and front side rear closing reinforcement (reus-
able).
1.
Front side closing plate reinforce-
ment
2.
Front side rear closing reinforcement
: Vehicle front
Replacement parts
z
Upper hoodledge (LH)
z
Hoodledge reinforcement (LH)
z
Front strut housing (LH)
z
Hoodledge reinforcement gusset
JSKIA2656ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст