Nissan Cube. Instruction — part 179
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
DEF-103
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
If No CAN Communication Is Available With BCM
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
FRONT WIPER CONTROL
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop five times.
Control part
Fail-safe operation
Cooling fan
• The cooling fan relay-1, the cooling fan relay-2 and the cooling fan relay-3 turn ON
when the ignition switch is turned ON (Cooling fan HI operation)
• The cooling fan relay-1, the cooling fan relay-2 and the cooling fan relay-3 turn OFF
when the ignition switch is turned OFF
A/C compressor
A/C relay OFF
Alternator
Outputs the power generation command signal (PWM signal) 0%
Control part
Fail-safe operation
Headlamp
• Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamps
• Side marker lamps
• License plate lamps
• Illuminations
• Tail lamps
• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
Front wiper
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-
safe control is activated while the front wiper is set in the INT mode and the front wiper
motor is operating.
Front fog lamps
Front fog lamp relay OFF
Horn
Horn OFF
Ignition relay
The status just before activation of fail-safe is maintained.
Starter motor
Starter control relay OFF
Voltage judgment
IPDM E/R judgment
Operation
Ignition relay contact side
Ignition relay excitation coil
side
ON
ON
Ignition relay ON normal
—
OFF
OFF
Ignition relay OFF normal
—
ON
OFF
Ignition relay ON stuck
• Detects DTC “B2098: IGN RELAY ON”
• Turns ON the tail lamp relay for 10 min-
utes
OFF
ON
Ignition relay OFF stuck
Detects DTC “B2099: IGN RELAY OFF”
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop
position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does
not change for 10 seconds.
DEF-104
< ECU DIAGNOSIS INFORMATION >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
WITH INTELLIGENT KEY : DTC Index
INFOID:0000000010246442
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now.
- The number increases like 1
→
2 ··· 38
→
39 after returning to the normal condition whenever IGN OFF
→
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×
: Applicable
WITHOUT INTELLIGENT KEY
WITHOUT INTELLIGENT KEY : Reference Value
INFOID:0000000010246444
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT display
Fail-safe
Refer to
No DTC is detected.
further testing
may be required.
—
—
U1000: CAN COMM CIRCUIT
×
B2098: IGN RELAY ON CIRC
×
B2099: IGN RELAY OFF CIRC
—
B210B: STR CONT RLY ON CIRC
—
B210C: STR CONT RLY OFF CIRC
—
B210D: STARTER RLY ON CIRC
—
B210E: STARTER RLY OFF CIRC
—
B210F: INTRLCK/PNP SW ON
—
B2110: INTRLCK/PNP SW OFF
—
Monitor Item
Condition
Value/Status
MOTOR FAN REQ
Engine idle speed
Changes depending on engine
coolant temperature, air conditioner
operation status, vehicle speed,
etc.
1/2/3/4
AC COMP REQ
Engine running
A/C switch OFF
Off
A/C switch ON
(Compressor is operating)
On
TAIL&CLR REQ
Lighting switch OFF
Off
Lighting switch 1ST, 2ND, HI or AUTO (Light is illuminated)
On
HL LO REQ
Lighting switch OFF
Off
Lighting switch 2ND, HI or AUTO (Light is illuminated)
On
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
DEF-105
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
HL HI REQ
Lighting switch OFF
Off
Lighting switch HI
On
FR FOG REQ
Lighting switch 2ND or
AUTO (Light is illuminated)
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
FR WIP REQ
Ignition switch ON
Front wiper switch OFF
Stop
Front wiper switch INT
1LOW
Front wiper switch LO
Low
Front wiper switch HI
Hi
WIP AUTO STOP
Ignition switch ON
Front wiper stop position
STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT
Ignition switch ON
Front wiper operates normally
Off
Front wiper stops at fail-safe opera-
tion
BLOCK
IGN RLY
Ignition switch OFF or ACC
Off
Ignition switch ON
On
INTER/NP SW
Ignition switch ON
Selector lever in any position other
than P or N (CVT models)
Off
Selector lever in P or N position
(CVT models)
On
ST RLY -REQ
Ignition switch OFF or ACC
Off
Ignition switch ON
On
DTRL REQ
NOTE:
The item is indicated, but not monitored.
Off
OIL P SW
Ignition switch OFF, ACC or engine running
Open
Ignition switch ON
Close
HOOD SW
NOTE:
The item is indicated, but not monitored.
Off
THFT HRN REQ
Not operation
Off
• Panic alarm is activated
• Horn is activated with VEHICLE SECURITY (THEFT WARNING) SYS-
TEM
On
HORN CHIRP
Not operating
Off
Door locking with key fob (horn chirp mode)
On
Monitor Item
Condition
Value/Status
DEF-106
< ECU DIAGNOSIS INFORMATION >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
TERMINAL LAYOUT
PHYSICAL VALUES
JPMIA1512ZZ
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
1
(R)
Ground
Battery power supply
Input
Ignition switch OFF
Battery voltage
2
(G)
Ground
Battery power supply
Input
Ignition switch OFF
Battery voltage
3
(BR)
Ground
Starter motor
Output
Ignition switch ON
0 V
At engine cranking
Battery voltage
5
(LG)
Ground
Cooling fan relay-1
power supply
Output
Cooling fan OFF
0 V
Cooling fan operated
Battery voltage
6
(SB)
Ground
Ignition switch START
Output
Any position other ignition switch
START
0 V
Ignition switch START
Battery voltage
7
(Y)
Ground
Cooling fan relay-2
power supply
Output
Cooling fan OFF
0 V
Cooling fan LO operated
9.0 V
Cooling fan HI operated
Battery voltage
8
(V)
Ground
Battery power supply
Input
Ignition switch OFF
Battery voltage
9
(B/W)
Ground
Ground
—
Ignition switch ON
0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст