Nissan Cube. Instruction — part 527
REAR DOOR GLASS
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000009949316
Removal and Installation
INFOID:0000000009949317
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Fully open rear door glass.
3.
Remove power window switch finisher bracket. Refer to
4.
Remove rear door speaker harness connector and rear sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
5.
Remove rear door outside molding. Refer to
EXT-26, "Removal and Installation"
.
6.
Remove partition sash mounting bolts and screw.
7.
Remove partition sash.
• Remove rear door glass run from partition sash.
1.
Rear door panel
2.
Rear door sealing screen
3.
Rear door glass run
4.
Partition sash
5.
Partition weather-strip
6.
Partition glass
7.
Rear door glass
8.
Power window motor
9.
Regulator assembly
10. Rear door sash
: Clip
: Vehicle front
JMKIA3944ZZ
GW-24
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
• Slightly pull straight down partition sash.
• From the upper side, slop partition sash toward vehicle front and then remove.
8.
Operate the power window switch to raise/lower the door win-
dow until the glass mounting bolts can be seen.
9.
Remove the glass mounting bolts (A).
10. Remove rear door glass from the rear door panel.
11. Remove partition glass.
• Slide partition glass toward the arrow 1.
• Pull partition toward the direction of arrow 2 to remove.
• Remove partition weather-strip after removing the partition
glass.
12. Remove rear door glass run fixing clip and remove rear door glass run.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000009949318
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and carrier plate
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
JMKIA3948ZZ
JMKIA3949ZZ
REAR REGULATOR
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR REGULATOR
Exploded View
INFOID:0000000009949319
Removal and Installation
INFOID:0000000009949320
REMOVAL
1.
Remove rear door glass. Refer to
GW-23, "Removal and Installation"
.
2.
Disconnect power window motor harness connector (A).
3.
Remove the regulator assembly mounting bolts (C), nuts (B) and
remove regulator assembly from door panel.
1.
Rear door panel
2.
Rear door sealing screen
3.
Rear door glass run
4.
Partition sash
5.
Partition weather-strip
6.
Partition glass
7.
Rear door glass
8.
Power window motor
9.
Regulator assembly
10. Rear door sash
: Clip
: Vehicle front
JMKIA3944ZZ
JMKIA3945ZZ
GW-26
< REMOVAL AND INSTALLATION >
REAR REGULATOR
4.
Remove rear door sash mounting bolts and then remove rear door lower sash.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000009949321
DISASSEMBLY
Remove power window motor from regulator assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000009949322
Inspection after Removal
Check the regulator assembly for the following items. Replace or grease it if a malfunction is detected.
• Wire wear
• Regulator deformation
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and carrier plate
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст