Nissan Cube. Instruction — part 784
COIL SPRING
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
COIL SPRING
Exploded View
INFOID:0000000009948847
Removal and Installation
INFOID:0000000009948848
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Set jack under rear suspension beam.
CAUTION:
Check the stable condition when using a jack.
3.
Remove right and left rear shock absorber mounting bolts (lower side). Refer to
.
4.
Slowly lower jack, then remove upper rubber seat, coil spring and lower rubber seat from rear suspension
beam.
CAUTION:
Check the stable condition when using a jack.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the lower rubber seat a projection (A) is attached as rear
suspension beam mounting hole (B).
• Match up lower rubber seat indentions and rear suspension beam
grooves and attach.
Inspection
INFOID:0000000009948849
INSPECTION AFTER REMOVAL
Check rubber seat and coil spring for deformation, crack, and damage. Replace it if necessary.
1.
Upper rubber seat
2.
Coil spring
3.
Lower rubber seat
4.
Rear suspension beam
JPEIB0162ZZ
JPEIB0177ZZ
RSU-10
< REMOVAL AND INSTALLATION >
COIL SPRING
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor. Refer to
REAR SUSPENSION BEAM
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION BEAM
Exploded View
INFOID:0000000009948850
Removal and Installation
INFOID:0000000009948851
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Drain brake fluid. Refer to
3.
Remove parking brake cable and brake drum from rear suspension beam. Refer to
,
4.
Remove wheel sensor and sensor harness. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
5.
Set suitable jack under rear suspension beam.
CAUTION:
Check the stable condition when using a jack.
6.
Remove shock absorber mounting bolts (lower side). Refer to
.
7.
Remove coil springs. Refer to
8.
Separate brake hose and brake tube. Refer to
.
9.
Remove suspension arm bracket mounting bolts.
10. Slowly lower jack, remove suspension arm bracket and rear suspension beam from vehicle body.
CAUTION:
Check the stable condition when using a jack.
11. Remove wheel hub and bearing assembly. Refer to
12. Remove drum brake assembly. Refer to
13. Remove suspension arm bracket from rear suspension beam.
14. Remove brake tube protector from rear suspension beam.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension beam installation position (rubber bushing), under unladen condi-
tions with tires on level ground.
• Refill with new brake fluid and perform the air bleeding. Refer to
1.
Rear suspension beam
2.
Brake tube protector
3.
Rear suspension arm bracket
A.
Flange bolt
B.
Except flange bolt
for symbols in the figure.
JPEIB0178GB
RSU-12
< REMOVAL AND INSTALLATION >
REAR SUSPENSION BEAM
Inspection
INFOID:0000000009948852
INSPECTION AFTER REMOVAL
Check rear suspension beam and rear suspension beam bracket for deformation, cracks or damage. Replace
the part if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake. Refer to
PB-3, "Inspection and Adjustment"
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст