Nissan Cube. Instruction — part 402
EM-12
< PREPARATION >
PREPARATION
(
—
)
Instruction lift table caddy
Removing and installing engine
(
—
)
Tube presser
Pressing the tube of liquid gasket
(Kent-Moore No.)
Tool name
Description
ZZA1210D
S-NT052
DRIVE BELT
EM-13
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PERIODIC MAINTENANCE
DRIVE BELT
Exploded View
INFOID:0000000009944915
Checking
INFOID:0000000009944916
WARNING:
Perform this step when engine is stopped.
• Check that the indicator (C) (notch on fixed side) of drive belt auto-tensioner is within the possible use range
(A) in the figure.
NOTE:
• Check the drive belt auto-tensioner indication when the engine is cold.
• When new drive belt is installed, the indicator (notch on fixed side) should be within the range (B) in the fig-
ure.
• Visually check entire drive belt for wear, damage or cracks.
• If the indicator (notch on fixed side) is out of the possible use range or belt is damaged, replace drive belt.
Tension Adjustment
INFOID:0000000009944917
Removal and Installation
INFOID:0000000009944918
REMOVAL
1.
Remove front wheel and tire (RH).
2.
Remove front fender protector (RH). Refer to
EXT-21, "FENDER PROTECTOR : Exploded View"
3.
Hold the hexagonal part (A) of drive belt auto-tensioner (1) with
a wrench securely. Then move the wrench handle in the direc-
tion of arrow (loosening direction of tensioner).
CAUTION:
Avoid placing hand in a location where pinching may occur
if the holding tool accidentally comes off.
4.
Insert a rod approximately 6 mm (0.24 in) in diameter such as
short-length screwdriver into the hole (B) of the retaining boss to
fix drive belt auto-tensioner.
• Keep drive belt auto-tensioner pulley arm locked after drive
belt is removed.
5.
Remove drive belt.
1.
Alternator
2.
Drive belt auto-tensioner
3.
Crankshaft pulley
4.
A/C compressor (models with A/C)
Idler pulley (models without A/C)
5.
Water pump
6.
Drive belt
A.
Possible use range
B.
Range when new drive belt is in-
stalled
C.
Indicator
PBIC3137J
Refer to
.
PBIC3936E
EM-14
< PERIODIC MAINTENANCE >
DRIVE BELT
INSTALLATION
1.
Install drive belt.
CAUTION:
• Confirm drive belt is completely set to pulleys.
• Check for engine oil, working fluid and engine coolant are not adhered to drive belt and each
pulley groove.
2.
Release drive belt auto-tensioner, and apply tension to drive belt.
3.
Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4.
Confirm tension of drive belt at indicator (notch on fixed side) is within the possible use range. Refer to
AIR CLEANER FILTER
EM-15
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER FILTER
Removal and Installation
INFOID:0000000009944919
REMOVAL
1.
Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2.
Pull up the air cleaner cover forward (C) and remove it.
3.
Remove the air cleaner filter (1) and holder (2) assembly from
the air cleaner case.
4.
Remove the air cleaner filter from the holder.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the air cleaner cover (1) in the direction as shown in the fig-
ure.
Inspection (Viscous Paper Type)
INFOID:0000000010208825
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• If clogging or damage is observed, replace the air cleaner element.
CAUTION:
Never clean the viscous paper type air cleaner element by blowing as there is a risk of deterioration of
its performance
MAINTENANCE INTERVAL
MA-6, "Introduction of Periodic Maintenance"
PBIC3557J
PBIC3558J
2
: Air cleaner filter
3
: Holder
PBIC3559J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст