Nissan Cube. Instruction — part 130
BODY ALIGNMENT
BRM-53
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Description
INFOID:0000000009949351
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
• When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
• Measurements should be taken at the center of the mounting holes.
• An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side
is symmetrically the same value.
• The coordinates of the measurement points are the distances measured from the standard line of
″
X
″
,
″
Y
″
and
″
Z
″
.
•
″
Z
″
: Imaginary base line [200 mm (7.87 in) below datum line (
″
0Z
″
at design plan)]
Engine Compartment
INFOID:0000000009949352
MEASUREMENT
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
D
Parking brake reinforcement
Hole
φ
12 (0.47)
E
Rear panel
Indent
Points
Portion
Marks
1.
Vehicle center
2.
Front axle center
3.
Imaginary base line
JSKIA0073GB
BRM-54
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
«The others»
Unit: mm (in)
MEASUREMENT POINTS
Unit: mm (in)
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
A - C
711 (27.99)*
B - d
1238 (48.74)*
C - c
1377 (54.21)
F - f
1297 (51.06)
A - F
800 (31.50)*
B - e
1473 (57.99)*
D - d
1037 (40.83)
B - C
159 (6.26)*
B - F
547 (21.54)*
E - e
1400 (55.12)
JSKIA1142GB
BODY ALIGNMENT
BRM-55
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Unit: mm (in)
Underbody
INFOID:0000000009949353
MEASUREMENT
: Vehicle front
JSKIA1143ZZ
Point
Material
Point
Material
A
Cowl top flange end of center positioning mark
G, g
Upper radiator core support hole center
φ
9 (0.35)
B, b
Hood hinge installing hole center
φ
11 (0.43)
H
Front side member hole center
φ
11 (0.43)
C, c, F, f
Front fender installing hole center
φ
7 (0.28)
h
Engine mounting bracket hole center
φ
11 (0.43)
D, d
Front strut installing hole center 11
×
16
(0.43
×
0.63)
J, j
Front side member reinforcement extension hole
center
J:
φ
14 (0.55)
j: 10
×
14 (0.39
×
0.55)
E, e
Hoodledge reinforcement hole center
φ
12 (0.47)
K, k
Front side member connector hole center
φ
16
(0.63)
BRM-56
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
The following figure shows a bottom view and a side view of the vehicle.
MEASUREMENT POINTS
Unit: mm (in)
: Vehicle front
JSKIA1144GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст