Nissan Cube. Instruction — part 621
INL-104
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
CONSULT display
Fail-safe
Tire pressure
monitor warn-
ing lamp ON
Reference
U1000: CAN COMM
—
—
U1010: CONTROL UNIT (CAN)
—
—
B2190: NATS ANTENNA AMP
×
—
B2191: DIFFERENCE OF KEY
×
—
B2192: ID DISCORD BCM-ECM
×
—
B2193: CHAIN OF BCM-ECM
×
—
B2195: ANTI SCANNING
×
—
C1704: LOW PRESSURE FL
—
×
C1705: LOW PRESSURE FR
—
×
C1706: LOW PRESSURE RR
—
×
C1707: LOW PRESSURE RL
—
×
C1708: [NO DATA] FL
—
×
C1709: [NO DATA] FR
—
×
C1710: [NO DATA] RR
—
×
C1711: [NO DATA] RL
—
×
C1716: [PRESS DATA ERR] FL
—
×
C1717: [PRESS DATA ERR] FR
—
×
C1718: [PRESS DATA ERR] RR
—
×
C1719: [PRESS DATA ERR] RL
—
×
C1729: VHCL SPEED SIG ERR
—
×
C1735: IGN CIRCUIT OPEN
—
—
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-105
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009950953
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
All the following lamps do not turn ON.
• Map lamp
• Room lamp
• Luggage room lamp
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp power supply cir-
cuit
Refer to
.
• Interior room lamp does not turn ON even
though the door is open.
(It turns ON when turning the interior room
lamp ON.)
• Interior room lamp does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
Door switch circuit
Refer to
.
Interior room lamp control circuit
Refer to
.
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
.
Push-button ignition switch illumination does not
illuminate.
• Harness between BCM and push-
button ignition switch
• Harness between push-button igni-
tion switch and ground
• Push-button ignition switch
• BCM
Push-button ignition switch illumina-
tion circuit
Refer to
.
Interior room lamp battery saver does not acti-
vate.
—
Check the interior room lamp battery
saver setting.
Refer to
.
INL-106
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009950954
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal
INFOID:0000000010262828
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
MAP LAMP
INL-107
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000009950955
Removal and Installation
INFOID:0000000009950956
CAUTION:
Disconnect the battery negative terminal or the fuse.
REMOVAL
1.
Insert any appropriate tool into the gap between the map lamp
bulb housing to the headlining. And press the pawl and then pull
the map lamp .
2.
Disconnect the connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009950957
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
MAP LAMP BULB
1.
Map lamp bulb housing
2.
Bulb
3.
Lens
JPLIA1645ZZ
JSLIA0110ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст