Nissan Cube. Instruction — part 713
PCS
B2614 ACC RELAY CIRCUIT
PCS-77
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC/CIRCUIT DIAGNOSIS
B2614 ACC RELAY CIRCUIT
Description
INFOID:0000000009945050
BCM controls the various electrical components and simultaneously supplies power according to the power
supply position.
BCM checks the power supply position internally.
DTC Logic
INFOID:0000000009945051
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the power supply position to ACC under the following conditions, and wait for 2 second or more.
-
Selector lever is in the P position
-
Do not depress brake pedal
2.
Check “Self-diagnosis result” of BCM with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009945052
1.
CHECK ACCESSORY RELAY POWER SUPPLY-1
1.
Turn ignition switch OFF.
2.
Disconnect accessory relay.
3.
Check voltage between accessory relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK ACCESSORY RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between accessory relay harness connector and BCM harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2614
BCM
An immediate operation of accessory relay is re-
quested by BCM, but there is no response for more
than 2 second.
• Harness or connectors
(Accessory relay circuit is open or
shorted)
• BCM
• Accessory relay
(+)
(–)
Condition
Voltage (V)
(Approx.)
Accessory relay
Terminal
1
Ground
Ignition switch
OFF
0
ACC or ON
12
Accessory relay
BCM
Continuity
Terminal
Connector
Terminal
1
M71
96
Existed
PCS-78
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B2614 ACC RELAY CIRCUIT
4.
Check continuity between accessory relay harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-89, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK ACCESSORY RELAY GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between accessory relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair accessory relay ground circuit.
4.
CHECK ACCESSORY RELAY POWER SUPPLY CIRCUIT-2
1.
Turn ignition switch ACC.
2.
Check voltage between accessory relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Check continuity open or short between accessory relay and battery.
5.
CHECK ACCESSORY RELAY
PCS-78, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace accessory relay.
6.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009945053
1.
CHECK ACCESSORY RELAY
1.
Turn ignition switch OFF.
2.
Remove accessory relay.
Accessory relay
Ground
Continuity
Terminal
1
Not existed
Accessory relay
Ground
Continuity
Terminal
2
Existed
(+)
(–)
Voltage (V)
(Approx.)
Accessory relay
Terminal
5
Ground
Battery voltage
PCS
B2614 ACC RELAY CIRCUIT
PCS-79
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
3.
Check the continuity between accessory relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace accessory relay
Terminals
Condition
Continuity
3 and 5
12 V direct current supply between terminals 1 and 2
Existed
No current supply
Not existed
PBIB0098E
PCS-80
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B2615 BLOWER RELAY CIRCUIT
B2615 BLOWER RELAY CIRCUIT
Description
INFOID:0000000009945054
BCM turns ON the following relays to ignition power supply to each ECU when the ignition switch is turned
ON.
• Ignition relay
• Ignition relay (inside IPDM E/R)
• Blower relay
BCM checks any blower relay ON request for consistency with the actual blower relay operation status.
DTC Logic
INFOID:0000000009945055
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for 1 second or more.
-
Selector lever is in the P position
-
Do not depress brake pedal
2.
Check “Self-diagnosis result” of BCM with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009945056
1.
CHECK BLOWER RELAY POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect blower relay.
3.
Check voltage between blower relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BLOWER RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between blower relay harness connector and BCM harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2615
BCM
BCM detects a difference of signal for 1 second or
more between the following items.
• Blower relay ON/OFF request
• Blower relay feedback
• Harness or connectors
(Blower relay circuit is open or
shorted)
• BCM
• Blower relay
(+)
(–)
Condition
Voltage (V)
(Approx.)
Blower relay
Terminal
1
Ground
Ignition switch
OFF or ACC
0
ON
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст