Nissan Cube. Instruction — part 592
HAC-206
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000009951111
Removal and Installation
INFOID:0000000009951112
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
26, "Perform Lubricant Return Operation"
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2.
Clean refrigerant pressure sensor and its surrounding area, and then remove dust and rust from refriger-
ant pressure sensor.
CAUTION:
Be sure to clean carefully.
3.
Disconnect refrigerant pressure sensor connector.
1.
Condenser
2.
Refrigerant pressure sensor
3.
O-ring
4.
Grommet
5.
Condenser seal
6.
Bracket
7.
O-ring
8.
Liquid tank bracket
9.
Liquid tank
Refer to
for symbols in the figure.
JPIIA1552GB
REFRIGERANT PRESSURE SENSOR
HAC-207
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
4.
Use a adjustable wrench (A) or other tool to hold the refrigerant
pressure sensor mounting block, and then remove the refriger-
ant pressure sensor (2) from the condenser (1).
CAUTION:
• Be careful not to damage liquid tank.
• Be careful not to damage core surface of condenser.
• Cap or wrap the joint of the condenser and liquid tank
with suitable material such as vinyl tape to avoid the entry
of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant. Refer to
JPIIA1708ZZ
HAC-208
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
BLOWER FAN RESISTOR
BLOWER FAN RESISTOR
Exploded View
INFOID:0000000009951113
Removal and Installation
INFOID:0000000009951114
REMOVAL
1.
Remove instrument panel assembly. Refer to
.
2.
Remove cowl top extension. Refer to
3.
Remove instrument stay.
4.
Remove mounting bolts (A), and then move steering member (1) to a position where it dose not inhibit
work.
5.
Disconnect blower fan resistor connector.
6.
Remove mounting screws (A), and then remove blower fan
resistor (1).
INSTALLATION
Installation is basically the reverse order of removal.
JPIIA1730ZZ
JPIIA1736ZZ
INTAKE DOOR MOTOR
HAC-209
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
INTAKE DOOR MOTOR
Exploded View
INFOID:0000000009951115
Removal and Installation
INFOID:0000000009951116
REMOVAL
1.
Remove foot duct LH. Refer to
2.
Remove mounting screws (A), and then remove intake door
motor (1).
3.
Disconnect intake door motor connector.
INSTALLATION
Installation is basically the reverse order of removal.
1.
A/C unit assembly
2.
Intake door lever
3.
Intake door motor
4.
Air mix door link
5.
Upper air mix door rod
6.
Air mix door cable
7.
Upper air mix door lever
8.
Lower air mix door lever
9.
Lower air mix door rod
A.
To A/C control
JPIIA1724ZZ
JPIIA1737ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст