Nissan Cube. Instruction — part 497
FAX-24
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT
c.
Install snap ring (1).
CAUTION:
Never reuse snap ring.
d.
Install dust shields.
CAUTION:
Never reuse dust shields.
2.
Install dynamic damper, follow the procedure described below.
a.
Install dynamic damper to shaft.
b.
Secure dynamic damper with bands in the following specified
position (A) when installing.
CAUTION:
Never reuse bands.
3.
Wrap serration on shaft with tape (A) to protect boot from dam-
age. Install new boot and boot bands to shaft.
CAUTION:
Never reuse boot and boot band.
4.
Remove the tape wrapped around the serration on shaft.
JPDIF0106ZZ
JPDIF0127ZZ
A
: Refer to
JPDIF0178ZZ
JPDIF0009ZZ
FRONT DRIVE SHAFT
FAX-25
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
5.
To install the spider assembly (1), align it with the matching
marks (A) on the shaft (2) during the removal, and direct the ser-
ration mounting surface (B) to the shaft.
6.
Secure spider assembly onto shaft with snap ring (1).
CAUTION:
Never reuse snap ring.
7.
Apply the appropriate amount of grease to spider assembly and
sliding surface.
8.
Assemble the housing onto spider assembly, and apply the bal-
ance of the specified amount grease.
9.
Align matching marks put during the removal of housing.
10. Install the boot, following the procedures below.
• Install boot securely into grooves (indicated by “*” marks)
shown in the figure (Except for CVT models).
CAUTION:
If grease adheres to the boot mounting surface (with “*”
mark) on shaft or housing, boot may be removed. Remove
all grease from the surface.
• Install boot securely into grooves (indicated by “*” marks)
shown in the figure (For CVT models).
CAUTION:
If grease adheres to the boot mounting surface (with “*”
mark) on shaft or housing, boot may be removed. Remove
all grease from the surface.
11. To prevent the deformation of the boot, adjust the boot installa-
tion length to the value shown below (L) by inserting the suitable
tool into the inside of boot from the large diameter side of boot
and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip of tool.
12. Secure housing and shaft, and then check that they are in the correct position when rotating boot. Install
them with new boot band when the mounting positions become incorrect.
Inspection
INFOID:0000000009948803
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
JPDIF0017ZZ
Grease amount
JPDIF0014ZZ
JPDIF0224ZZ
L
: Refer to
.
JPDIF0144ZZ
FAX-26
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Check the support bearing bracket for cracks, deformation and other damage.
INSPECTION AFTER DISASSEMBLY
Check the following items, and replace the part if necessary.
Shaft
Check shaft for runout, cracks, or other damage. Replace if necessary.
Dynamic Damper
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness.
• The inside of the joint sub-assembly for entry of foreign material.
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and spider assembly (Transaxle Side)
Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
Support Bearing (Right Side)
Check bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if there are
any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for support bearing bracket, cracks, or damage. Replace support bearing bracket if there are any non-
standard conditions.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-110, "FRONT WHEEL SENSOR :
.
2.
Adjust neutral position of steering angle sensor. Refer to
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-27
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009948804
Drive Shaft
INFOID:0000000009948805
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Item
Left side
Right side
Grease quantity
Wheel side
MT
80 – 100 g (2.83 – 3.52 oz)
CVT
77 – 97 g (2.72 – 3.42 oz)
Transaxle side
MT
130 – 140 g (4.59 – 4.93 oz)
CVT
113 – 123 g (3.99 – 4.33 oz)
Boots installed length
Wheel side
MT
141.7 mm (5.58 in)
CVT
136.0 mm (5.35 in)
Transaxle side
MT
155.7 mm (6.13 in)
167.7 mm (6.60 in)
CVT
153.6 mm (6.05 in)
148.6 mm (5.85 in)
Dimension of dynamic damper
MT
230 – 236 mm (9.06 – 9.29 in)
CVT
225 – 231 mm (8.86 – 9.09 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст