Nissan Cube. Instruction — part 904

B1147 CURTAIN AIR BAG MODULE RH

SRC-133

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1147 CURTAIN AIR BAG MODULE RH

Description

INFOID:0000000009946259

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946260

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-133, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946261

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to

SRC-133, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1147

CURTAIN MODULE
RH
[GND-SHORT]

Curtain air bag module RH circuit is shorted
to ground

• Disconnection of wiring harness and short
• Malfunction in curtain air bag module RH
• Malfunction in air bag diagnosis sensor unit

SRC-134

< DTC/CIRCUIT DIAGNOSIS >

B1147 CURTAIN AIR BAG MODULE RH

4.

REPLACE CURTAIN AIR BAG MODULE

1.

Replace curtain air bag module RH. Refer to

SR-20, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to

SRC-133, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

B1148 CURTAIN AIR BAG MODULE RH

SRC-135

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1148 CURTAIN AIR BAG MODULE RH

Description

INFOID:0000000009946262

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946263

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-135, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946264

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to

SRC-135, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1148

CURTAIN MODULE RH
[SHORT]

Curtain air bag module RH circuits are shorted
to each other

• Disconnection of wiring harness and short
• Malfunction in curtain air bag module RH
• Malfunction in air bag diagnosis sensor unit

SRC-136

< DTC/CIRCUIT DIAGNOSIS >

B1148 CURTAIN AIR BAG MODULE RH

4.

REPLACE CURTAIN AIR BAG MODULE

1.

Replace curtain air bag module RH. Refer to

SR-20, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to

SRC-135, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END