Nissan Cube. Instruction — part 597
INL-8
< SYSTEM DESCRIPTION >
INTERIOR ROOM LAMP CONTROL SYSTEM
• Each illumination (tail lamp) ON
• Any of the following conditions with ignition switch OFF
- Engine start permission is entered.
- Driver door is LOCK
→
UNLOCK.
- Driver door is open.
Push-button Ignition Switch Illumination OFF Operation
BCM turns the push-button ignition switch illumination OFF in any of the following conditions.
• The push-button ignition switch illumination ON conditions do not satisfy.
• All of the following conditions with ignition switch OFF.
- Each illumination (tail lamp) OFF
- The push-button ignition switch illumination ON conditions do not change (15 seconds after the ignition
switch OFF) or the driver door is UNLOCK
→
LOCK
Component Parts Location
INFOID:0000000009950914
Component Description
INFOID:0000000009950915
*1:With Intelligent Key
*2:Without Intelligent Key
1.
Room lamp
2.
Remote keyless entry receiver
Refer to
.
3.
.
4.
Door lock and unlock switch
5.
Door switch
6.
Request switch
7.
Map lamp
8.
Key switch
(Without Intelligent Key)
9.
Push switch
(With Intelligent Key)
JPLIA1817ZZ
Part
Description
BCM
Activates the interior room lamp timer depending on the vehicle condition to turn the
interior room lamps ON/OFF.
Remote keyless entry receiver
Receives the lock/unlock signal from Keyfob.
• Door lock and unlock switch
• Key cylinder lock and unlock switch
• Request switch
*1
Inputs the lock/unlock signal to BCM.
Door switch
Inputs the door switch signal to BCM.
• Key in switch
*2
• Push switch
*1
Inputs the key switch signal to BCM.
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
INL-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
System Diagram
INFOID:0000000009950916
WITH INTELLIGENT KEY
WITHOUT INTELLIGENT KEY
System Description
INFOID:0000000009950917
OUTLINE
• Interior room lamp battery saver is controlled by BCM.
• BCM turns applicable lamps OFF depending on the vehicle condition. This function prevents the battery
from over-discharging if the driver neglect turning OFF the any lamps.
Applicable lamps
• Map lamp
• Room lamp
• Luggage room lamp
INTERIOR ROOM LAMP BATTERY SAVER FUNCTION
• When the ignition switch is turned OFF, BCM operates the timer for a period of time to cut the interior room
lamp power supply.
• BCM restart the timer when any of the following signals changes while operating the timer.
- Ignition switch status
- Door switch signal (ALL)
- Door lock/unlock signal (Remote keyless entry receiver, each request switch
*1
, door lock and unlock switch,
key cylinder lock and unlock switch)
- Key switch signal
*2
JPLIA1814GB
JPLIA1816GB
INL-10
< SYSTEM DESCRIPTION >
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
- Push switch signal
*1
• BCM provides the interior room lamp power supply continuously when the ignition switch position is ON.
*1:With Intelligent Key
*2:Without Intelligent Key
NOTE:
Each function of interior room lamp battery saver can be set by CONSULT. Refer to
SAVER : CONSULT Function (BCM - BATTERY SAVER)"
.
Component Parts Location
INFOID:0000000009950918
Component Description
INFOID:0000000009950919
*1:With Intelligent Key
*2:Without Intelligent Key
1.
Room lamp
2.
Remote keyless entry receiver
Refer to
.
3.
BCM
Refer to
4.
Door lock and unlock switch
5.
Door switch
6.
Request switch
7.
Map lamp
8.
Key switch (Without Intelligent Key)
9.
Push switch (With Intelligent Key)
JPLIA1817ZZ
Part
Description
BCM
Operates the interior room lamp battery saver depending on the vehicle condition to
cut the interior room lamp power supply.
Remote keyless entry receiver
Receives the lock/unlock signal from keyfob.
• Door lock and unlock switch
• Key cylinder lock and unlock switch
• Request switch
*1
Inputs the lock/unlock signal to BCM.
Door switch
Inputs the door switch signal to BCM.
• Push switch
*1
• Key switch
*2
Inputs the key switch signal to BCM.
ILLUMINATION CONTROL SYSTEM
INL-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ILLUMINATION CONTROL SYSTEM
System Diagram
INFOID:0000000009950920
System Description
INFOID:0000000009950921
OUTLINE
Each illumination lamp is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Headlamp control function
Control by IPDM E/R
• Relay control function
ILLUMINATION CONTROL
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits position light request signal to IPDM E/R and combination meter according to tail lamp ON
condition.
Tail lamp ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment (With auto light system)
• IPDM E/R turns the integrated tail lamp relay ON according to position light request signal. It provides the
power supply to each illumination lamp.
• Combination meter illuminates the meter illumination according to position light request signal.
JPLIA0855GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст