Nissan Cube. Instruction — part 987
TM-204
< PRECAUTION >
[CVT: RE0F08B]
PRECAUTIONS
17
–5 (23)
196
105 (221)
21
0 (32)
201
110 (230)
27
5 (41)
206
115 (239)
32
10 (50)
210
120 (248)
39
15 (59)
214
125 (257)
47
20 (68)
218
130 (266)
55
25 (77)
221
135 (275)
64
30 (86)
224
140 (284)
73
35 (95)
227
145 (293)
83
40 (104)
229
150 (302)
93
45 (113)
231
155 (311)
104
50 (122)
233
160 (320)
114
55 (131)
235
165 (329)
124
60 (140)
236
170 (338)
134
65 (149)
238
175 (347)
143
70 (158)
239
180 (356)
152
75 (167)
241
190 (374)
161
80 (176)
243
200 (392)
169
85 (185)
—
—
ATFTEMP COUNT
Temperature
°
C (
°
F)
ATFTEMP COUNT
Temperature
°
C (
°
F)
PREPARATION
TM-205
< PREPARATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009949069
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009949070
Tool number
(Kent-Moore No.)
Tool name
Description
—
(OTC3492)
Oil pressure gauge set
Measuring line pressure
KV38107900
( — )
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
ST35325000
( — )
KV31103000
( — )
Drift
a: 70 mm (2.75 in) dia.
b: 59 mm (2.32 in) dia.
c: 49 mm (1.92 in) dia.
Installing differential side oil seal
SCIA7531E
PDIA1183J
ZZA0501D
Tool name
Description
Power tool
Loosening nuts and bolts
PBIC0190E
TM-206
< PERIODIC MAINTENANCE >
[CVT: RE0F08B]
CVT FLUID
PERIODIC MAINTENANCE
CVT FLUID
Inspection
INFOID:0000000009949071
Level check
Check fluid level in HOT state [CVT fluid temperature is between 50 to 80
°
C (122 to 176
°
F)], according to the
following procedures.
1.
Visually check that CVT fluid leakage from transaxle assembly is not detected.
2.
After engine warms up, drive the vehicle in an urban area for approximately 10 minutes.
NOTE:
When ambient temperature is 20
°
C (68
°
F), driving vehicle for approximately 10 minutes in an urban area
ordinarily warms up CVT fluid temperature between 50 to 80
°
C (122 to 176
°
F).
3.
Park the vehicle on a level surface.
4.
Fully apply parking brake.
5.
Adjust engine speed at idle state.
6.
Shift selector lever through entire position from “P” to “D” while depressing brake pedal.
7.
Press claw of CVT fluid level gauge lock to unlock.
8.
Remove CVT fluid level gauge from CVT fluid charging pipe.
9.
Wipe CVT fluid that is on CVT fluid level gauge.
CAUTION:
Always use shop paper when wiping off CVT fluid that is on
CVT fluid level gauge.
10. Rotate CVT fluid level gauge 180
°
from installed state.
11. Inset CVT fluid level gauge until it contacts CVT fluid charging
pipe end.
12. Check that CVT fluid level is within the specified level of CVT fluid level gauge (MAX side).
CAUTION:
• After level check, when returning CVT fluid level gauge to the original state, insert CVT fluid level
gauge to CVT fluid charging pipe until it is locked.
• Always use shop paper when wiping off CVT fluid that is on CVT fluid level gauge.
CVT FLUID CONDITION
SCIA1933E
SCIA1931E
CVT FLUID
TM-207
< PERIODIC MAINTENANCE >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of tran-
saxle assembly. Flush cooling system after repair of transaxle
assembly.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of transaxle assembly. Refer to
231, "CVT FLUID COOLER HOSE : Exploded View"
.
Changing
INFOID:0000000009949072
1.
Remove drain plug from oil pan and then the CVT fluid.
2.
Remove drain plug gasket from drain plug.
3.
Install drain plug gasket to drain plug.
CAUTION:
Never reuse drain plug gasket.
4.
Install drain plug to oil pan.
5.
Fill CVT fluid from CVT fluid charging pipe to the specified level.
CAUTION:
• Always use the specified fluid. If use, misuse, or mixing of fluid other than the specified fluid
occurs, original performance cannot be obtained or it may cause serious malfunctions.
• CVT fluid is not reusable. Never reuse CVT fluid.
• Always use shop paper. Never use shop cloth.
• After replacement, always perform CVT fluid leakage check.
• Delete CVT fluid deterioration date with CONSULT after changing CVT fluid.
6.
After engine warms up, drive the vehicle in an urban area for approximately 10 minutes.
NOTE:
When ambient temperature is 20
°
C (68
°
F), it takes about 10 minutes for the CVT fluid to warm up to 50 to
80
°
C (122 to 176
°
F).
7.
Check CVT fluid level and condition. Refer to
.
8.
Repeat steps 1 to 6 if CVT fluid has been contaminated.
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
CVT fluid become
degraded due to
high temperatures
• Replace the CVT fluid.
• Check the transaxle assembly
and the vehicle for malfunctions
(wire harnesses, cooler pipes,
etc.)
Milky white or
cloudy
Water in the fluid
• Replace the CVT fluid.
• Check for places where water is
getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
transaxle assembly
• Replace the CVT fluid.
• Check for improper operation of
the transaxle assembly.
ATA0022D
CVT fluid and fluid capacity
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст