Nissan Cube. Instruction — part 1078
FRONT WIPER DRIVE ASSEMBLY
WW-149
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000009945883
REMOVAL VIEW
DISASSEMBLY VIEW
Removal and Installation
INFOID:0000000009945884
REMOVAL
1.
Remove front wiper arm. Refer to
2.
Remove cowl top cover. Refer to
1.
Front wiper drive assembly
Refer to
JPLIA1764GB
1.
Front wiper linkage 2
2.
Front wiper frame
3.
Shaft seal
4.
Front wiper motor
5.
Front wiper linkage 1
: Multi
−
purpose grease or an equivalent
JPLIA1765ZZ
WW-150
< REMOVAL AND INSTALLATION >
FRONT WIPER DRIVE ASSEMBLY
3.
Remove bolts from the front wiper drive assembly.
4.
Disconnect the front wiper motor connector.
5.
Remove front wiper drive assembly from the vehicle.
INSTALLATION
1.
Install the front wiper drive assembly to the vehicle.
2.
Connect the front wiper motor connector.
3.
Operate the front wiper to move it to the auto stop position.
4.
Install the cowl top cover. Refer to
5.
Install front wiper arms. Refer to
Disassembly and Assembly
INFOID:0000000009945885
DISASSEMBLY
1.
Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when removing the front wiper
linkage.
2.
Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1.
Connect the front wiper motor connector.
2.
Operate the front wiper to move it to the auto stop position.
3.
Disconnect the front wiper motor connector.
4.
Install front wiper motor to front wiper frame.
5.
Install the front wiper linkage 1 to the front wiper motor and the front wiper frame.
6.
Install the front wiper linkage 2 to the front wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply multi
−
purpose grease or an equivalent if necessary.
WIPER AND WASHER SWITCH
WW-151
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER AND WASHER SWITCH
Exploded View
INFOID:0000000009945886
WW-152
< REMOVAL AND INSTALLATION >
REAR WIPER ARM
REAR WIPER ARM
Exploded View
INFOID:0000000009945887
Removal and Installation
INFOID:0000000009945888
REMOVAL
1.
Operate the rear wiper to the auto stop position.
2.
Remove the rear wiper arm cover.
3.
Remove the rear wiper arm mounting nut.
4.
Raise rear wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.
2.
Operate the rear wiper motor to the auto stop position.
3.
Adjust the rear wiper blade position. Refer to
4.
Install the rear wiper arm by tightening the mounting nut.
5.
Inject the washer fluid.
6.
Operate the rear wiper to the auto stop position.
7.
Check that the rear wiper blades stop at the specified position.
8.
Install the rear wiper arm cover.
Adjustment
INFOID:0000000009945889
REAR WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of back door glass and the top of wiper blade center.
1.
Rear wiper motor
2.
Rear wiper blade
3.
Rear wiper arm
4.
Rear wiper arm cover
5.
pivot seal
Refer to
for symbols in the figure.
JPLIA1820GB
SKIA0082J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст