Nissan Cube. Instruction — part 231
DLK-190
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
FRONT DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000009950609
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009950610
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove front door harness grommet, and then pull out the harness from the vehicle.
3.
Disconnect front door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-191, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Sealing screen
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3956ZZ
FRONT DOOR
DLK-191
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Adjustment
INFOID:0000000009950611
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door hinge (upper)
6.
Front door hinge (lower)
7.
Rear door hinge (upper)
8.
Rear door hinge (lower)
9.
Door striker
10.
TORX bolt
Refer to
for symbols in the figure.
JMKIA3837GB
DLK-192
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
Unit : mm (in)
1.
Remove front fender. Refer to
DLK-188, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install front fender. Refer to refer to
DLK-188, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000009950612
DOOR STRIKER : Removal and Installation
INFOID:0000000009950613
REMOVAL
Portion
Clearance
Surface height
Front fender – Front door
A – A
3.5 – 5.5 (0.138 – 0.217)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
- 1.0 – 1.0 (- 0.039 – 0.039)
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Sealing screen
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3956ZZ
FRONT DOOR
DLK-193
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000009950614
DOOR HINGE : Removal and Installation
INFOID:0000000009950615
REMOVAL
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-188, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-190, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Sealing screen
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3956ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст