Nissan Cube. Instruction — part 387
EC-434
< ECU DIAGNOSIS INFORMATION >
[MR18DE]
ECM
34
(R)
36
(Y)
Throttle position sensor 2
Input
[Ignition switch: ON]
• Engine stopped
• Selector lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released
Less than 4.75 V
[Ignition switch: ON]
• Engine stopped
• Selector lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully depressed
More than 0.36 V
36
(Y)
—
Sensor ground
(Throttle position sensor)
—
—
—
37
(W)
40
(—)
Knock sensor
Input
[Engine is running]
• Idle speed
2.5 V
38
(BR)
44
(GR)
Engine coolant tempera-
ture sensor
Input
[Engine is running]
0 - 4.8 V
Output voltage varies with engine
coolant temperature.
40
(—)
—
Sensor ground
(Knock sensor)
—
—
—
41
(GR)
48
(BR)
Refrigerant pressure sen-
sor
Input
[Engine is running]
• Warm-up condition
• Both A/C switch and blower fan mo-
tor switch: ON (Compressor oper-
ates)
1.0 - 4.0 V
42
(V)
51
(Y)
EVAP control system
pressure sensor
Input
[Ignition switch: ON]
1.8 - 4.8 V
43
(P)
108
(B)
Fuel tank temperature
sensor
Input
[Engine is running]
0 - 4.8 V
Output voltage varies with fuel
tank temperature.
44
(GR)
—
Sensor ground
(Engine coolant tempera-
ture sensor)
—
—
—
45
(G)
52
(R)
Mass air flow sensor
Input
[Engine is running]
• Warm-up condition
• Idle speed
0.7 - 1.1 V
[Engine is running]
• Warm-up condition
• Engine speed : 2,500 rpm
1.3 - 1.7 V
46
(L)
55
(P)
Intake air temperature
sensor
Input
[Engine is running]
0 - 4.8 V
Output voltage varies with intake
air temperature.
48
(BR)
—
Sensor ground
(Refrigerant pressure
sensor)
—
—
—
49
(V)
53
(LG)
A/F sensor 1
Input
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm
Approximately 1.8 V
Output voltage varies with air fuel
ratio.
50
(W)
59
(O)
Heated oxygen sensor 2
Input
[Engine is running]
• Revving engine from idle to 3,000
rpm quickly after the following condi-
tions are met
- Engine: after warming up
- Keeping the engine speed between
3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load
0 - 1.0 V
Terminal No.
Description
Condition
Value
(Approx.)
+
−
Signal name
Input/
Output
ECM
EC-435
< ECU DIAGNOSIS INFORMATION >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
51
(Y)
—
Sensor ground
(EVAP control system
pressure sensor)
—
—
—
52
(R)
—
Sensor ground
(Mass air flow sensor)
—
—
—
53
(LG)
—
Sensor ground
(A/F sensor 1)
—
—
—
55
(P)
—
Sensor ground
(Intake air temperature
sensor)
—
—
—
57
(GR)
64
(SB)
Battery current sensor
Input
[Engine is running]
• Battery: Fully charged
*1
• Idle speed
2.6 - 3.5 V
59
(O)
—
Sensor ground
(Heated oxygen sensor 2)
—
—
—
61
(W)
62
(B)
Crankshaft position sen-
sor (POS)
Input
[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
4.0 V
[Engine is running]
• Engine speed: 2,000 rpm
4.0 V
62
(B)
—
Sensor ground
[Crankshaft position sen-
sor (POS)]
—
—
—
63
(L)
—
Sensor ground
[Camshaft position sen-
sor (PHASE)]
—
—
—
64
(SB)
—
Sensor ground
(Battery current sensor)
—
—
—
Terminal No.
Description
Condition
Value
(Approx.)
+
−
Signal name
Input/
Output
JMBIA0333GB
JMBIA0334GB
EC-436
< ECU DIAGNOSIS INFORMATION >
[MR18DE]
ECM
65
(Y)
63
(L)
Camshaft position sensor
(PHASE)
Input
[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle
0 - 5.0
[Engine is running]
• Engine speed is 2,000 rpm
0 - 5.0
66
(L)
108
(B)
Power supply for ECM
(Back-up)
Input
[Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14 V)
71
(Y)
108
(B)
Sensor power supply
[Battery current sensor]
—
[Ignition switch: ON]
5 V
72
(O)
36
(Y)
Sensor power supply
(Throttle position sensor)
—
[Ignition switch: ON]
5 V
73
(P)
108
(B)
Intake valve timing control
solenoid valve
Output
[Engine is running]
• Warm-up condition
• Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• When revving engine up to
2,000rpm Quickly
7 - 10 V
74
(W)
108
(B)
Sensor power supply
(Refrigerant pressure
sensor)
Input
[Ignition switch: ON]
5 V
75
(R)
62
(B)
Sensor power supply
[Crankshaft position sen-
sor (POS)]
—
[Ignition switch: ON]
5 V
76
(LG)
51
(Y)
Sensor power supply
[EVAP control system
pressure sensor]
—
[Ignition switch: ON]
5 V
78
(G)
63
(L)
Sensor power supply
[Camshaft position sen-
sor (PHASE)]
—
[Ignition switch: ON]
5 V
83
(P)
108
(B)
CAN communication line
Input/
Output
—
—
84
(L)
108
(B)
CAN communication line
Input/
Output
—
—
88
(LG)
108
(B)
Data link connector
Input/
Output
—
—
Terminal No.
Description
Condition
Value
(Approx.)
+
−
Signal name
Input/
Output
JMBIA0045GB
JMBIA0046GB
PBIA4937J
ECM
EC-437
< ECU DIAGNOSIS INFORMATION >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
93
(L)
108
(B)
Ignition switch
Input
[Ignition switch: OFF]
0 V
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
94
(SB)
95
(BR)
*2
(B)
*3
ASCD steering switch
Input
[Ignition switch: ON]
• ASCD steering switch: OFF
4 V
[Ignition switch: ON]
• MAIN switch: Pressed
0 V
[Ignition switch: ON]
• CANCEL switch: Pressed
1 V
[Ignition switch: ON]
• RESUME/ACCELERATE switch:
Pressed
3 V
[Ignition switch: ON]
• SET/COAST switch: Pressed
2 V
95
(BR)
*2
(B)
*3
—
Sensor ground
(ASCD steering switch)
—
—
—
99
(W)
108
(B)
Stop lamp switch
Input
[Ignition switch: OFF]
• Brake pedal: Fully released
0 V
[Ignition switch: OFF]
• Brake pedal: Slightly depressed
BATTERY VOLTAGE
(11 - 14 V)
100
(SB)
108
(B)
ASCD brake switch
Input
[Ignition switch: ON]
• Brake pedal: Slightly depressed
(CVT)
• Brake pedal and clutch pedal:
Slightly depressed (M/T)
0 V
[Ignition switch: ON]
• Brake pedal: Fully released (CVT)
• Brake pedal and/or clutch pedal:
Fully released (M/T)
BATTERY VOLTAGE
(11 - 14 V)
102
(O)
108
(B)
Sensor power supply
(Accelerator pedal posi-
tion sensor 2)
—
[Ignition switch: ON]
5 V
103
(G)
104
(R)
Accelerator pedal posi-
tion sensor 2
Input
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released
0.3 - 0.6 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed
1.95 - 2.4 V
104
(R)
—
Sensor ground
(Accelerator pedal posi-
tion sensor 2)
—
—
—
105
(G)
108
(B)
Power supply for ECM
Input
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
106
(V)
108
(B)
Sensor power supply
(Accelerator pedal posi-
tion sensor 1)
—
[Ignition switch: ON]
5 V
Terminal No.
Description
Condition
Value
(Approx.)
+
−
Signal name
Input/
Output
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст