Nissan Cube. Instruction — part 655

ENGINE OIL

LU-9

< PERIODIC MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

A

LU

N

P

O

3.

Install oil pressure gauge [SST: ST25051001 (J-25695-1)] (A)
and hose [SST: ST25052000 (J-25695-2)] (B).

4.

Start engine and warm it up to normal operating temperature.

5.

Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.

If difference is extreme, check oil passage and oil pump for oil leakage.

6.

After the inspections, install oil pressure switch as follows:

a.

Remove old liquid gasket adhering to oil pressure switch and engine.

b.

Apply liquid gasket and tighten oil pressure switch to specification.
Use Genuine RTV Silicon Sealant or equivalent. Refer to

GI-22, "Recommended Chemical Prod-

ucts and Sealants"

.

c.

Check engine oil level. Refer to

LU-8, "Inspection"

.

d.

After warming up engine, check that there is no leakage of engine oil with running engine.

Draining

INFOID:0000000009950379

WARNING:

• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin

contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.

1.

Warm up the engine, and check for engine oil leakage from engine components. Refer to

LU-8, "Inspec-

tion"

.

2.

Stop the engine and wait for 10 minutes.

3.

Loosen oil filler cap.

4.

Remove drain plug and then drain engine oil.

Refilling

INFOID:0000000009950380

1.

Install drain plug with new drain plug washer. Refer to

EM-32, "Exploded View"

.

CAUTION:

Be sure to clean drain plug and install with new drain plug washer.

2.

Refill with new engine oil.
Engine oil specification and viscosity: Refer to

MA-10, "Fluids and Lubricants"

.

CAUTION:

JPBIA0074ZZ

Engine oil pressure

: Refer to

LU-15, "Engine Oil Pressure"

.

Tightening torque

: Refer to

EM-86, "Exploded View"

.

Tightening torque

: Refer to

EM-32, "Exploded View"

.

Engine oil capacity

: Refer to

LU-15, "Periodical Maintenance Specification"

.

LU-10

< PERIODIC MAINTENANCE >

ENGINE OIL

• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-

tions for reference only.

• Always use oil level gauge to determine the proper amount of engine oil in the engine.

3.

Warm up engine and check area around drain plug and oil filter for engine oil leakage.

4.

Stop engine and wait for 10 minutes.

5.

Check the engine oil level. Refer to

LU-8, "Inspection"

.

OIL FILTER

LU-11

< PERIODIC MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

A

LU

N

P

O

OIL FILTER

Removal and Installation

INFOID:0000000009950381

REMOVAL

1.

Remove engine under cover. Refer to

EXT-22, "Exploded View"

.

2.

Using oil filter wrench [SST: KV10115801 (J-38956)] (A), remove
oil filter.

CAUTION:

• Oil filter is provided with relief valve. Use genuine NISSAN

oil filter or equivalent.

• Be careful not to get burned when engine and engine oil

may be hot.

• When removing, prepare a shop cloth to absorb any

engine oil leakage or spillage.

• Completely wipe off any engine oil that adheres to engine

and vehicle.

INSTALLATION

1.

Remove foreign materials adhering to the oil filter installation surface.

2.

Apply new engine oil to the oil seal contact surface of new oil fil-
ter.

3.

Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.

Inspection

INFOID:0000000009950382

INSPECTION AFTER INSTALLATION

1.

Check the engine oil level. Refer to

LU-8, "Inspection"

.

2.

Start the engine, and check that there is no leakage of engine oil.

3.

Stop the engine and wait for 10 minutes.

4.

Check the engine oil level, and adjust the level. Refer to

LU-8, "Inspection"

.

: Vehicle front

PBIC3312J

SMA010

Oil filter:

: 17.7 N·m (1.8 kg-m, 13 ft-lb)

JPBIA0077ZZ

LU-12

< REMOVAL AND INSTALLATION >

OIL PUMP

REMOVAL AND INSTALLATION

OIL PUMP

Exploded View

INFOID:0000000009950383

1.

Oil level gauge

2.

Oil level gauge guide

3.

Rear oil seal

4.

O-ring

5.

Oil pan (upper)

6.

Oil pump drive chain

7.

Crankshaft sprocket

8.

Oil pump sprocket

9.

Oil pump chain tensioner

10. Oil pump

11.

Drain plug

12. Drain plug washer

13. Oil pan (lower)

14. Oil filter

15. Connector bolt

16. O-ring

A.

Comply with the assembly procedure
when tightening. Refer to

LU-11

B.

Oil pan side

: Always replace after every disassembly.

: Should be lubricated with oil.

: Sealing point

PBIC4463J