Nissan Cube. Instruction — part 1067
BCM (BODY CONTROL MODULE)
WW-105
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
JRMWE7829GB
WW-106
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
JRMWE7830GB
BCM (BODY CONTROL MODULE)
WW-107
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WITHOUT INTELLIGENT KEY : Fail-safe
INFOID:0000000010278008
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
JRMWE7831GB
WW-108
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper auto stop signal.
When the rear wiper auto stop signal does not change more than 5 seconds while driving the rear wiper, BCM
stops power supply to protect the rear wiper motor.
Condition of cancellation
1.
Pass more than 1 minute after the rear wiper stop.
2.
Turn rear wiper switch OFF.
3.
Operate the rear wiper switch or rear washer switch.
WITHOUT INTELLIGENT KEY : DTC Inspection Priority Chart
INFOID:0000000010278009
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
WITHOUT INTELLIGENT KEY : DTC Index
INFOID:0000000010278010
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF
→
ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→
2
→
3...38
→
39 after returning to the normal condition whenever ignition switch OFF
→
ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF
→
ON after returning to the normal condition if the malfunction is detected again.
Display contents of CONSULT
Fail-safe
Cancellation
B2190: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2191: DIFFERENCE OF KEY
Inhibit engine cranking
Erase DTC
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2195: ANTI SCANNING
Inhibit engine cranking
Ignition switch ON
→
OFF
Priority
DTC
1
• U1000: CAN COMM
• U1010: CONTROL UNIT (CAN)
2
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
3
C1735: IGN CIRCUIT OPEN
4
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1729: VHCL SPEED SIG ERR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст