Nissan Cube. Instruction — part 439
EXL-30
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JPMIA1486GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger
ground circuit
• Harness or connector be-
tween IPDM E/R and rear
window defogger
• IPDM E/R
Any of the following components do not operate
• Parking lamps
• Side marker lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (HI, LO)
• Front wiper (HI, LO)
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground cir-
cuit
• Harness or connector be-
tween IPDM E/R and appli-
cable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal
between A/C amp. and
ECM
• CAN communication signal
between ECM and IPDM E/
R
NO
• Magnet clutch
• Harness or connector be-
tween IPDM E/R and mag-
net clutch
• IPDM E/R
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
EXL-31
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
CONSULT Function (IPDM E/R)
INFOID:0000000010249364
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
EXL-166, "WITH INTELLIGENT KEY : DTC Index"
.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Oil pressure warning lamp does not operate
Perform auto active test.
Does the oil pressure warning
lamp blink?
YES
• Harness or connector be-
tween IPDM E/R and oil
pressure switch
• Oil pressure switch
• IPDM E/R
NO
• CAN communication signal
between IPDM E/R and
BCM
• CAN communication signal
between BCM and combi-
nation meter
• Combination meter
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal
between ECM and IPDM E/
R
NO
• Cooling fan motor
• Harness or connector be-
tween IPDM E/R and cool-
ing fan motor
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
EXL-32
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
ACTIVE TEST
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN
communication.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the clutch interlock switch (M/T models) or shift position
(CVT models) judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN
communication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN
communication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]
Displays the status of the starter relay and starter control relay judged by IPDM
E/R.
DETENT SW
[Off/On]
Displays the status of the CVT shift selector (detention switch) judged by IPDM E/
R.
S/L RLY -REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
S/L STATE
[LOCK/UNLOCK/UNKWN]
NOTE:
The item is indicated, but not monitored.
DTRL REQ
[Off/On]
NOTE:
The item is indicated, but not monitored.
OIL P SW
[Open/Close]
Displays the status of the oil pressure switch judged by IPDM E/R.
HOOD SW
[Off/On]
NOTE:
The item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder signal received from BCM via CAN com-
munication.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Operates the cooling fan relay (LO operation).
3
Operates the cooling fan relay (HI operation).
4
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
EXL-33
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
ond intervals.
Fog
Operates the front fog lamp relay.
Test item
Operation
Description
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст