Nissan Cube. Instruction — part 339
EC-242
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
P0335 CKP SENSOR (POS)
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009947360
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK CRANKSHAFT POSITION (CKP) SENSOR (POS) POWER SUPPLY CIRCUIT-I
1.
Disconnect crankshaft position (CKP) sensor (POS) harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between CKP sensor (POS) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 3.
3.
CHECK CKP SENSOR (POS) POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch ON.
2.
Disconnect ECM harness connector.
3.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit.
4.
CHECK CKP SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
CKP sensor (POS)
Ground
Voltage
Connector
Terminal
F20
1
Ground
Approx. 5 V
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F20
1
F8
75
Existed
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F8
74
Refrigerant pressure sensor
E49
3
75
CKP sensor (POS)
F20
1
76
EVAP control system pressure sen-
sor
B21
3
77
Battery current sensor
F53
1
E16
102
APP sensor
E110
5
P0335 CKP SENSOR (POS)
EC-243
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair short to ground or short to power in harness or connectors.
5.
CHECK COMPONENTS
Check the following.
• Buttery current sensor (Refer to
EC-337, "Component Inspection"
.)
• EVAP control system pressure sensor (Refer to
EC-279, "Component Inspection"
.)
• Refrigerant pressure sensor (Refer to
.)
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace malfunctioning components.
6.
CHECK APP SENSOR
EC-385, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 7.
7.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
EC-385, "Special Repair Requirement"
>> INSPECTION END
8.
CHECK CKP SENSOR (POS) GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
3.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check the continuity between CKP sensor (POS) harness connector and ECM harness connector.
3.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-244, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Replace crankshaft position sensor (POS). Refer to
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F20
2
F8
62
Existed
CKP sensor (POS)
ECM
Continuity
Connector
Terminal
Connector
Terminal
F20
3
F8
61
Existed
EC-244
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
P0335 CKP SENSOR (POS)
11.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Replace the signal plate. Refer to
.
12.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009947361
1.
CHECK CRANKSHAFT POSITION SENSOR (POS)-I
1.
Turn ignition switch OFF.
2.
Loosen the fixing bolt of the sensor.
3.
Disconnect crankshaft position sensor (POS) harness connector.
4.
Remove the sensor. Refer to
5.
Visually check the sensor for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace crankshaft position sensor (POS). Refer to
.
2.
CHECK CRANKSHAFT POSITION SENSOR (POS)-II
Check resistance between crankshaft position sensor (POS) terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace crankshaft position sensor (POS). Refer to
PBIA9209J
Terminals (Polarity)
Resistance [
Ω
at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
1 (+) - 3 (-)
2 (+) - 3 (-)
P0340 CMP SENSOR (PHASE)
EC-245
< DTC/CIRCUIT DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0340 CMP SENSOR (PHASE)
Description
INFOID:0000000009947362
The camshaft position sensor (PHASE) senses the retraction of
camshaft (INT) to identify a particular cylinder. The camshaft position
sensor (PHASE) senses the piston position.
When the crankshaft position sensor (POS) system becomes inoper-
ative, the camshaft position sensor (PHASE) provides various con-
trols of engine parts instead, utilizing timing of cylinder identification
signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor changes.
ECM receives the signals as shown in the figure.
DTC Logic
INFOID:0000000009947363
DTC DETECTION LOGIC
NOTE:
If DTC P0340 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V with igni-
tion switch ON.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
1.
Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2.
Check 1st trip DTC.
PBIA9875J
JMBIA0714GB
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0340
Camshaft position sensor
(PHASE) circuit
• The cylinder No. signal is not sent to ECM for
the first few seconds during engine cranking.
• The cylinder No. signal is not sent to ECM
during engine running.
• The cylinder No. signal is not in the normal
pattern during engine running.
• Harness or connectors
(The sensor circuit is open or shorted)
• Camshaft position sensor (PHASE)
• Camshaft (INT)
• Starter motor
• Starting system circuit
• Dead (Weak) battery
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст