Nissan Cube. Instruction — part 802
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
SEC-19
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Component Parts Location
INFOID:0000000009950091
1.
CVT shift selector (detention switch)
M58
2.
NATS antenna amp. M26
3.
Push-button ignition switch M101
4.
Remote keyless entry receiver M87
Refer to
KEY SYSTEM :
Component Parts Location"
5.
ABS actuator and electric unit (con-
trol unit) E36
Refer to
6.
Inside key antenna (instrument cen-
ter) M105
7.
Stop lamp switch E115
8.
Horn E50, E51
9.
Transmission range switch F21
10. IPDM E/R E10, E11, E12, E13, E14,
.
11.
ECM E16
12. TCM E18
13. BCM M68, M69, M70, M71
.
14. Security indicator lamp
(combination meter) M34
15. Front door switch (driver side) B34
16. Inside key antenna (luggage room)
B82
A.
Behind push-button ignition switch
B.
Behind instrument lower cover LH
JMKIA4036ZZ
SEC-20
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
Component Description
INFOID:0000000009950092
Component Reference
BCM
Push-button ignition switch
Door switch
CVT shift selector (detention switch)
Stop lamp switch
TCM
Starter relay
Starter control relay
Security indicator lamp
VEHICLE SECURITY SYSTEM
SEC-21
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY SYSTEM
System Diagram
INFOID:0000000009950093
System Description
INFOID:0000000009950094
OPERATION FLOW
SETTING THE VEHICLE SECURITY SYSTEM
Initial Condition
• Ignition switch is in the OFF position.
Disarmed Phase
• When any door is open, the vehicle security system is set in the disarmed phase on the assumption that the
owner is inside or near the vehicle.
JMKIA4034GB
JMKIA2505GB
SEC-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM
• When the vehicle security system is in the disarmed phase, the security indicator lamp blinks every 2.4 sec-
onds.
Pre-armed Phase and Armed Phase
When the following operation 1 or 2 is performed, the vehicle security system turns into the “pre-armed”
phase. (Security indicator lamp illuminates.)
1.
BCM receives LOCK signal from door lock and unlock switch, door key cylinder switch door request
switch or Intelligent Key, after all doors are closed.
2.
All doors are closed after all doors are locked by mechanical key or door lock and unlock switch.
CANCELING THE ARMED PHASE VEHICLE SECURITY SYSTEM
When one of the following operations is performed, the armed phase is canceled.
1.
Unlock all doors with the door lock and unlock switch, door key cylinder switch door request switch or
Intelligent Key.
2.
Turn ignition switch “ON” or “ACC” position.
CANCELING THE ALARM OPERATION OF THE VEHICLE SECURITY SYSTEM
When on of the following operations is performed, the alarm operation is canceled.
1.
Unlock all doors with the door request switch or Intelligent Key.
2.
Turn ignition switch “ON” or “ACC” position.
ACTIVATING THE ALARM OPERATION OF THE VEHICLE SECURITY SYSTEM
Check that the system is in the armed phase. (Security indicator lamp blinks every 2.4 seconds.)
When the following operations 1 or 2 is performed, the system sounds the horns and blinks the headlamps for
about 50 seconds.
1.
Any door is open during the armed phase.
2.
Disconnecting and connecting the battery connector before canceling the armed phase.
PANIC ALARM OPERATION
When BCM receives panic alarm signal from Intelligent Key, ground is supplied intermittently to both head-
lamp relay and horn relay.
When headlamp relay and horn relay are energized, then power is supplied to headlamps (HI) and horn.
The headlamp (HI) blinks and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds or when BCM receives any signal from Intelligent Key or
door request switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст