Nissan Cube. Instruction — part 407
EM-32
< REMOVAL AND INSTALLATION >
OIL PAN (LOWER)
OIL PAN (LOWER)
Exploded View
INFOID:0000000009944937
Removal and Installation
INFOID:0000000009944938
REMOVAL
1.
Drain engine oil. Refer to
.
1.
Oil level gauge
2.
Oil level gauge guide
3.
Rear oil seal
4.
O-ring
5.
Oil pan (upper)
6.
Oil pump drive chain
7.
Crankshaft sprocket
8.
Oil pump sprocket
9.
Oil pump chain tensioner
10. Oil pump
11.
Drain plug
12. Drain plug washer
13. Oil pan (lower)
14. Oil filter
15. Connector bolt
16. O-ring
A.
Comply with the assembly proce-
dure when tightening. Refer to
B.
Oil pan side
: Always replace after every disassembly.
: Should be lubricated with oil.
: Sealing point
PBIC4463J
OIL PAN (LOWER)
EM-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Remove oil pan (lower) with the following procedure:
a.
Loosen mounting bolts in the order of 10 to 1 as shown in the
figure.
b.
Insert seal cutter [SST: KV10111100 (J-37228)] (A) between oil
pan (upper) and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• Never insert a screwdriver. This damages the mating sur-
faces.
c.
Slide the seal cutter [SST: KV10111100 (J-37228)] by tapping on
the side of tool with a hammer.
d.
Remove oil pan (lower).
INSTALLATION
CAUTION:
Do not reuse drain plug washer.
1.
Install oil pan (lower) as follows:
a.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surface when cleaning
off old liquid gasket.
: Engine front
PBIC3146J
JPBIA0276ZZ
PBIC3953E
EM-34
< REMOVAL AND INSTALLATION >
OIL PAN (LOWER)
b.
Apply a continuous bead of liquid gasket (A) with a tube presser
(commercial service tool) as shown in the figure.
Use Genuine RTV Silicon Sealant or equivalent. Refer to
22, "Recommended Chemical Products and Sealants"
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
c.
Tighten bolts in the order of 1 to 10 as shown in the figure.
2.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
.
3.
Install in the reverse order of removal after this step.
Inspection
INFOID:0000000009944939
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leakage of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
1
: Oil pan (lower)
: Engine outside
PBIC4590E
: Engine front
PBIC3146J
FUEL INJECTOR AND FUEL TUBE
EM-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000009944940
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
Removal and Installation
INFOID:0000000009944941
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
REMOVAL
1.
Release the fuel pressure. Refer to
.
2.
Remove intake manifold. Refer to
1.
Fuel feed tube
2.
Bracket
3.
Quick connector cap
4.
Fuel tube
5.
O-ring (black)
6.
Clip
7.
Injector
8.
O-ring (green)
A.
To centralized under-floor piping
: Always replace after every disassembly.
: Should be lubricated with oil.
PBIC3537J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст