Nissan Cube. Instruction — part 915
ST-2
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009949808
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
NVH in F
AX, RAX
, FSU, RSU section
NVH in WT
se
ct
io
n
NVH in WT
se
ct
io
n
NVH in F
AX section
NVH in BR section
Possible cause and SUSPECTED PARTS
Oute
r/in
ne
r s
o
c
k
e
t b
a
ll jo
in
t s
w
ing
in
g
t
o
rq
ue
Oute
r/in
ne
r socke
t b
a
ll jo
in
t ro
ta
ti
ng
to
rqu
e
Oute
r/in
ne
r s
o
c
k
e
t b
a
ll jo
in
t e
n
d
pl
ay
S
te
e
ri
ng
whe
e
l pl
ay
Im
prop
er st
eeri
n
g
whe
e
l
Im
prop
er
in
st
a
lla
ti
on
or l
o
o
s
e
n
e
s
s
o
f ti
lt
loc
k
le
ve
r
M
ou
nt
ing
l
o
os
en
es
s
S
tee
rin
g
c
o
lu
m
n
d
e
fo
rm
at
io
n
or da
ma
ge
Im
prop
er
in
st
a
lla
ti
on
or l
o
o
s
e
n
e
s
s
o
f s
tee
rin
g
c
o
lu
m
n
S
tee
rin
g l
inka
ge
lo
os
en
es
s
AXLE
and
SUSPENSION
TIRE
ROA
D
WHEEL
DRIVE SHA
F
T
BRAKE
Symptom
Steering
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
PRECAUTIONS
ST-3
< PRECAUTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009949809
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Notice or Precautions for Steering System
INFOID:0000000009949810
• In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehicle
condition, and then check wheel alignment.
• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming
contaminated by dirt or other foreign matter.
- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with
their operation.
- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.
ST-4
< PRECAUTION >
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010078173
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
PREPARATION
ST-5
< PREPARATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009949811
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST3127S000
(J-25765-A)
Preload gauge
• Measuring steering column rotating torque
• Measuring pinion rotating torque
ST27180001
(J-25726-A)
Steering wheel puller
Removing steering wheel
KV48103400
(
—
)
Preload adapter
Measuring pinion rotating torque
KV40107300
(
—
)
Boot band crimping tool
Installing boot clamp (large diameter)
ZZA0806D
ZZA0819D
ZZA0824D
ZZA1229D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст