Nissan Cube. Instruction — part 272
DLK-354
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Exploded View
INFOID:0000000009950802
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009950803
CAUTION:
Perform work with 2 workers, because of its heavy weight.
REMOVAL
1.
Remove back door finisher lower. Refer to
INT-27, "Removal and Installation"
2.
Remove luggage side finisher (LH) (upper/lower). Refer to
INT-24, "Removal and Installation"
.
1.
Back door weather-strip
2.
Back door hinge (upper)
3.
Back door hinge (lower)
4.
Door check link
5.
Grommet
6.
Dovetail male
7.
Dovetail female
8.
Sealing screen
9.
Bumper rubber
10. Back door panel
A
: Center mark
Refer to
for symbols in the figure.
JMKIA6716GB
BACK DOOR
DLK-355
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove ground bolt (A) and disengage connections of harness
connectors (B) and rear washer hose (C).
4.
Remove back door harness grommet, and then pull out the harness from the vehcle.
5.
Support back door with the proper material to prevent it from falling.
6.
Remove mounting bolt of door check link on the vehcle.
7.
Remove back door hinge mounting bolts (back door side), and then remove back door assembly.
8.
Remove the following parts after removing back door assembly.
• Back door finisher upper
• Sealing screen
• Dovetail (male)
• Dovetail (female)
• Door check link
• Grommet
• Bumper rubber
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close, lock/unlock operation after installation.
• After installation, perform fitting adjustment. Refer to
DLK-356, "BACK DOOR ASSEMBLY : Adjust-
JMKIA3963ZZ
DLK-356
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000009950804
Check the clearance and the surface height between back door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Back door panel
2.
Back door hinge
3.
TORX bolt
4.
Back door striker
5.
Back door bumper rubber
6.
Roof panel
7.
Side window glass
8.
Back door glass
9.
Body side outer panel
10. Back door finisher
Refer to
for symbols in the figure.
JMKIA6717GB
BACK DOOR
DLK-357
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
1.
Loosen back door striker mounting bolts.
2.
Loosen bumper rubber.
3.
Adjust right and left clearances and clearances between rear bumper to the standard value specified in
the table, by taping back door striker using a rubber hammer and adjusting back door striker and bumper
rubber.
4.
Finally tighten back door hinge, bumper rubber, and back door striker.
CAUTION:
• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that becomes parallel with back door lock insertion direction.
BACK DOOR STRIKER
Portion
Standard
Difference
(RH/LH)
Back door – Roof
A – A
E
Clearance
6.1 – 9.9 (0.240 – 0.390)
—
F
Surface height
-0.6 – 1.4 (-0.024 – 0.055)
—
Side window glass – Back door
glass
B – B
G
Clearance
4.4 – 8.4 (0.173 – 0.331)
< 2.0 (0.079)
H
Surface height
0 – 2.0 (0 – 0.079)
—
Body side outer panel – Back
door
C – C
I
Clearance
4.0 – 6.0 (0.157 – 0.236)
< 1.0 (0.039)
J
Surface height
-1.0 – 1.0 (-0.039 – 0.039)
—
Back door – Back door finisher
D – D
K
Clearance
5.0 – 9.0 (0.197 – 0.354)
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст