Nissan Cube. Instruction — part 869
SR-22
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000009946910
Removal and Installation
INFOID:0000000009946911
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the front bumper fascia. Refer to
.
2.
Remove the fixing nut (A), and pull back crash zone sensor (1)
and bracket (2).
3.
Disconnect the crash zone sensor harness connector.
1.
Crash zone sensor
2.
Bracket
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JMHIA1039GB
JMHIA1062ZZ
CRASH ZONE SENSOR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed driver air bag module, deployed passenger air bag mod-
ule or seat belt pre-tensioner.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing nut after removal, replace with the new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the crash zone sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
SR-24
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
SATELLITE SENSOR
Exploded View
INFOID:0000000009946912
Removal and Installation
INFOID:0000000009946913
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the center pillar lower garnish. Refer to
.
2.
Remove the satellite sensor fixing nut.
3.
Disconnect the harness connector and then remove the satellite sensor.
CAUTION:
1.
Satellite sensor
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JMHIA1336GB
SATELLITE SENSOR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Never impact the satellite sensor.
• Replace the satellite sensor if it has been dropped or sus-
tained an impact.
• Replace the satellite sensor of deployed side air bag module and deployed curtain air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing nut after removal, replace with the new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the satellite sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст