Nissan Cube. Instruction — part 244
DLK-242
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010254845
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Automatic air conditioner
AIR CONDITONER
×
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
DIAGNOSIS SYSTEM (BCM)
DLK-243
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in
the P position (CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000009950685
BCM CONSULT FUNCTION
CONSULT performs the following functions via CAN communication with BCM.
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”
*
)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK”
*
to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
*
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”
*
.) to low power consumption mode
LOCK
Power supply position is “LOCK”
*
OFF
Power supply position is “OFF” (Ignition switch OFF)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DLK-244
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function
DATA MONITOR
The BCM input/output signals are displayed
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM
Monitor item
Description
DOOR LOCK-UNLOCK SET
Selective unlock function mode can be changed to operate with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE: All doors are locked when shifting the selector lever from P position to other than the
P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: door unlock operation only
• Lock Only: door lock operation only
• Lock/Unlock: lock/unlock operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of driver side door
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
SHOCK SENSOR
NOTE:
This item is displayed, but cannot be supported
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
DIAGNOSIS SYSTEM (BCM)
DLK-245
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ACTIVE TEST
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT)
INFOID:0000000009950686
BCM CONSULT FUNCTION
CONSULT performs the following functions via CAN communication with BCM.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
Monitor Item
Contents
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is touched
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function
DATA MONITOR
The BCM input/output signals are displayed
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM
Monitor Item
Condition
IGN ON SW
Indicates [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicates [On/Off] condition of key switch
ACC ON SW
Indicates [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
Indicates [On/Off] condition of unlock signal from keyfob
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be tested
DOOR SW-DR
Indicates [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicates [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicates [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicates [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicates [On/Off] condition of back door switch
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be tested
CDL LOCK SW
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS PANIC
Indicates [On/Off] condition of PANIC button of keyfob
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст