Nissan Cube. Instruction — part 627
BODY SIDE TRIM
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Remove front pillar garnish.
• Insert a remover tool between front pillar garnish and body
panel.
• Disengage metal clip, clip and pawls.
• Pull out front pillar garnish to remove.
FRONT KICKING PLATE INNER
1.
Pull up front kicking plate to disengage the pawls.
2.
Remove front kicking plate from the body panel.
DASH SIDE FINISHER
1.
Remove front kicking plate inner.
2.
Disengage dash side finisher fixing clip and pawl with remover
tool.
3.
Pull back dash side finisher to remove it from metal clip.
NOTE:
The metal clip remain on the body side after removal of dash
side finisher.
REAR KICKING PLATE INNER
Disengage rear dash side finisher fixing pawls and remove it.
FRONT BODY SIDE WELT
1.
Remove front kicking plate inner.
2.
Remove dash side finisher.
3.
Remove front body side welt from panel flange.
REAR BODY SIDE WELT
1.
Remove rear kicking plate inner.
: Clip
: Pawl
: Metal clip
JMJIA2902ZZ
: Pawl
JMJIA2903ZZ
: Clip
: Pawl
: Metal clip
JMJIA3028ZZ
: Pawl
JMJIA2890ZZ
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2.
Remove rear body side welt from panel flange.
CENTER PILLAR LOWER GARNISH
1.
Remove front kicking plate inner.
2.
Remove rear kicking plate inner.
3.
Remove front and rear body side welt.
4.
Remove front seatbelt floor anchor bolts (LH/RH). Refer to
SB-7, "SEAT BELT RETRACTOR : Removal
5.
Pull center pillar lower garnish crosswise to disengage the fixing
pawls as shown in the figure by the arrow 1.
6.
Pull back center pillar lower garnish to disengage the fixing
metal clips.
7.
Remove center pillar lower garnish from body panel.
CENTER PILLAR UPPER GARNISH
1.
Remove center pillar lower garnish.
2.
Remove front seatbelt shoulder anchor bolt. Refer to
SB-6, "SEAT BELT RETRACTOR : Exploded View"
.
3.
Remove front and rear body side welt.
4.
Remove the bolt cover and the bolt behind that cover.
5.
Pull up center pillar upper garnish to remove.
INSTALLATION
CAUTION:
When installing, check that clips, pawls and metal clips are securely fitted in panel holes on body, and
then press them in.
: Pawl
: Metal clip
JMJIA2891ZZ
FLOOR TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000009949270
Removal and Installation
INFOID:0000000009949271
REMOVAL
1.
Remove front seat assembly (LH/RH). Refer to
SE-14, "Removal and Installation"
.
2.
Remove rear seat cushion and seatback assembly (with rear seat). Refer to
.
3.
Remove instrument lower cover, glove box lid and instrument lower panel. Refer to
.
4.
Remove front seatbelt anchor bolt. Refer to
SB-8, "SEAT BELT BUCKLE : Exploded View"
.
5.
Remove front and rear kicking plate inner. Refer to
INT-16, "Removal and Installation"
6.
Remove dash side finisher. Refer to
INT-16, "Removal and Installation"
7.
Remove center pillar lower garnish. Refer to
INT-16, "Removal and Installation"
.
8.
Remove front body side welt and rear body side welt. Refer to
INT-16, "Removal and Installation"
.
1.
Floor trim
2.
Floor hook
3.
Front floor spacer RH
4.
Front floor spacer LH
5.
Rear floor spacer LH
6.
Luggage floor spacer front
7.
Luggage floor spacer rear
8.
Tool box
9.
Tool box cover
10.
Rear floor spacer RH
: Vehicle front
JMJIA3030ZZ
INT-20
< REMOVAL AND INSTALLATION >
FLOOR TRIM
9.
Remove front floor bracket (1) mounting nuts (A) and then
remove front floor bracket.
10. Disconnect airbag harness connector and remove drain hose.
11. Remove floor carpet fixing clip (A).
12. Remove luggage rear plate. Refer to
INT-24, "Removal and Installation"
13. Remove luggage side lower finisher (LH/RH). Refer to
INT-24, "Removal and Installation"
.
14. Remove floor carpet through the back door.
INSTALLATION
Install in the reverse order of removal.
JMJIA3037ZZ
: Metal clip
JMJIA2905ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст