Nissan Cube. Instruction — part 1028
PRECAUTIONS
WT-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010169641
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal
INFOID:0000000010169645
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Service Notice and Precautions for TPMS
INFOID:0000000009949835
• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low
tire pressure. Erase the self-diagnosis memories for Tire Pressure Monitoring System (TPMS), or register
the ID to turn low tire pressure warning lamp OFF. For ID registration, refer to
.
SEF289H
WT-4
< PRECAUTION >
PRECAUTIONS
• ID registration is required when replacing or rotating wheels, replacing tire pressure sensor or BCM. Refer to
.
• Replace grommet seal, valve core and valve cap of tire pressure sensor in TPMS, when replacing each tire
by reaching the wear limit. Refer to
WT-48, "WITH INTELLIGENT KEY : Exploded View"
(With intelligent key
system),
WT-51, "WITHOUT INTELLIGENT KEY : Exploded View"
(Without intelligent key system).
• Because the tire pressure sensor conforms to North America radio law, the following items must be
observed.
- The sensor may be used only in North America.
- It may not be used in any method other than the specified method.
- It must not be disassembled or modified.
Service Notice and Precautions for Road Wheel
INFOID:0000000009949836
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Never apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.
PREPARATION
WT-5
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009949837
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000009949838
Tool number
(Kent-Moore No.)
Tool name
Description
–
(J-45295)
Tire pressure sensor activation tool
Tire pressure sensor wake-up procedure and
ID registration
SEIA0462E
Tool name
Description
Power tool
Loosening wheel nuts
PBIC0190E
WT-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009949839
Component Description
INFOID:0000000009949840
1.
Tire pressure sensor
2.
Tire pressure receiver
A.
Wheel
B.
Low tire pressure warning lamp
(On the combination meter)
C.
BCM
Refer to
(With intelligent key sys-
(Without intelligent key
system).
D.
Glove box assembly
JSEIA0490ZZ
Component parts
Function
BCM (Body Control Module)
.
Tire pressure sensor
Tire pressure receiver
WT-7, "Tire pressure receiver"
.
Turn signal lamp
ID registration of each wheel has been completed, turn signal lamp flashes.
Combination meter
Transmits the vehicle speed signal via CAN communication to BCM.
Receives the following signals via CAN communication for BCM.
• Low tire pressure warning lamp signal
• TPMS malfunction warning lamp signal
Low tire pressure warning lamp
WT-8, "TIRE PRESSURE MONITORING SYSTEM : System Description"
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст