Nissan March K13. Instruction — part 85
B2623 INSIDE ANTENNA
DLK-51
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace inside key antenna (luggage room). (New antenna or other antenna)
2.
Connect BCM connector and inside key antenna (luggage room) connector.
3.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (luggage room).
NO
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
BCM
Inside key antenna (luggage room)
Continuity
Connector
Terminal
Connector
Terminal
M71
88
B82
1
Existed
89
2
BCM
Ground
Continuity
Connector
Terminal
M71
88
Not existed
89
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
Luggage
room
M71
88, 89
Ground
When Intelligent Key is in the
antenna detection area
When Intelligent Key is not in
the antenna detection area
JMKIA3839GB
JMKIA3838GB
DLK-52
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2626 OUTSIDE ANTENNA
B2626 OUTSIDE ANTENNA
DTC Logic
INFOID:0000000005948835
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Outside key antenna (driver side) is OK.
Diagnosis Procedure
INFOID:0000000005948836
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (driver side) connector.
2.
Check continuity between BCM harness connector and outside key antenna (driver side) harness connec-
tor.
DTC
CONSULT-III display
description
DTC detecting condition
Possible cause
B2626
OUTSIDE ANTENNA
An excessive high or low voltage from outside key
antenna (driver side) is sent to BCM
• Outside key antenna (driver side)
• Between BCM
∼
Outside key an-
tenna (driver side)
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
Driver side
M71
78, 79
Ground
When Intelligent Key is in the
antenna detection area
When Intelligent Key is not in
the antenna detection area
JMKIA3839GB
JMKIA3838GB
B2626 OUTSIDE ANTENNA
DLK-53
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace outside key antenna (driver side). (New antenna or other antenna)
2.
Connect BCM connector and outside key antenna (driver side) connector.
3.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace outside key antenna (driver side).
NO
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
BCM
Outside key antenna (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M71
78
D32
1
Existed
79
2
BCM
Ground
Continuity
Connector
Terminal
M71
78
Not existed
79
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
Driver side
M71
78, 79
Ground
When Intelligent Key is in
the antenna detection area
When Intelligent Key is not
in the antenna detection
area
JMKIA3839GB
JMKIA3838GB
DLK-54
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2627 OUTSIDE ANTENNA
B2627 OUTSIDE ANTENNA
DTC Logic
INFOID:0000000005948838
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is outside key antenna DTC detected?
YES
>> Refer to
.
NO
>> Outside key antenna (passenger side) is OK.
Diagnosis Procedure
INFOID:0000000005948839
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (passenger side) connector.
2.
Check continuity between BCM harness connector and outside key antenna (passenger side) harness
connector.
DTC
CONSULT-III display
description
DTC detecting condition
Possible cause
B2627
OUTSIDE ANTENNA
An excessive high or low voltage from outside key
antenna (passenger side) is sent to BCM
• Outside key antenna (passenger
side)
• Between BCM
∼
Outside key an-
tenna (passenger side)
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
Passenger
side
M71
80, 81
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA3838GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст