Nissan March K13. Instruction — part 268
EM-6
< PRECAUTION >
[HR12DE]
PRECAUTIONS
• As for bolt holes (B), normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Check to read the text of this instruction.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe them.
A
: Groove
: Inside
JPBIA0010ZZ
PREPARATION
EM-7
< PREPARATION >
[HR12DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000005988163
Tool number
Tool name
Description
KV10111100
Seal cutter
Removing oil pan (upper and lower) etc.
KV10116200
Valve spring compressor
1. KV10115900
Attachment
2. KV10109220
Adapter
Disassembling and assembling valve mecha-
nism
Part (1) is a component of KV10116200, but
Part (2) is not so.
KV10112100
Angle wrench
Tightening bolts for main bearing cap, cylinder
head, etc.
KV10117100
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor 1
For 22 mm (0.87 in) width hexagon nut
KV10107902
Valve oil seal puller
Removing valve oil seal
KV10115600
Valve oil seal drift
Installing valve oil seal
Use side A (G).
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421)
c: 10.3 (0.406) dia. f: 5 (0.20)
H: Side B
Unit: mm (in)
S-NT046
PBIC1650E
S-NT014
NT379
NT011
JPBIA0396ZZ
EM-8
< PREPARATION >
[HR12DE]
PREPARATION
Commercial Service Tools
INFOID:0000000005988164
EM03470000
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
Pilot bushing puller
Removing pilot converter
KV11103000
Pulley puller
Removing crankshaft pulley
KV11105210
Stopper plate
Fixing drive plate
Tool number
Tool name
Description
S-NT044
S-NT045
NT676
ZZA0009D
Tool name
Description
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
Pulley holder
Crankshaft pulley removing and installing
JPBIA0399ZZ
ZZA1010D
PREPARATION
EM-9
< PREPARATION >
[HR12DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Valve seat cutter set
Finishing valve seat dimensions
Piston ring expander
Removing and installing piston ring
Valve guide drift
Removing and installing valve guide
Valve guide reamer
1: Reaming valve guide inner hole
2: Reaming hole for oversize valve guide
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new air fuel ratio sensor
(Use with anti-seize lubricant shown below.)
A: [18 mm (0.71 in) dia.] for zirconia heated
oxygen sensor
B: [12 mm (0.47 in) dia.] for titania heated
oxygen sensor
C: Mating surface shave cylinder
D: Flutes
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
Tool name
Description
S-NT048
S-NT030
PBIC4012E
PBIC4013E
JPBIA0238ZZ
AEM489
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст