Nissan March K13. Instruction — part 365
A/C UNIT ASSEMBLY
HA-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
A/C UNIT ASSEMBLY
Exploded View
INFOID:0000000006032340
REMOVAL
DISASSEMBLY
1.
A/C unit assembly
2.
Cap
3.
Cap
4.
Steering member
for symbols in the figure.
JMIIA0591GB
HA-40
< REMOVAL AND INSTALLATION >
A/C UNIT ASSEMBLY
Heater & cooling unit
JMIIA0747GB
1.
Packing
2.
Packing
3.
A/C unit case assembly
4.
Blower motor
5.
Foot duct RH
6.
Evaporator pipe assembly
7.
O-ring
8.
Expanrion valve
9.
Gromet
10. Evaporator
11.
Intake sensor
12. Packing
13. Heater pipe cover
14.
Heater core
15. Packing
16. Front intake case
17.
Intake door
18. Sub intake door
19. Rear intake case
20.
Filter cover
21. Foot duct LH
22. Aspirator
23.
Aspirator hose
24. Air mix door
25. Center plate
26.
Foot door
27. Ventilator door
for symbols in the figure.
A/C UNIT ASSEMBLY
HA-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Heater unit
JMIIA0751ZZ
1.
Packing
2.
Packing
3.
Heater unit case assembly
4.
Blower motor
5.
Foot duct RH
6.
Patch
7.
Packing
8.
Heater pipe flange
9.
Heater core
10. Packing
11.
Front intake case
12. Intake door
13. Sub intake door
14.
Rear intake case
15. Foot duct LH
16. Filter cover
17.
Air mix door
18. Center plate
19. Foot door
20.
Ventilator door
for symbols in the figure.
HA-42
< REMOVAL AND INSTALLATION >
A/C UNIT ASSEMBLY
Ventilation unit
A/C UNIT ASSEMBLY
A/C UNIT ASSEMBLY : Removal and Installation
INFOID:0000000006032343
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
22, "Perform Lubricant Return Operation"
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
. (If equipped)
2.
Drain engine coolant from cooling system. Refer to
. (If equipped)
3.
Remove front wiper drive assembly. Refer to
WW-54, "Removal and Installation"
4.
Remove mounting bolt, and then disconnect low-pressure flexible hose and high-pressure pipe from
expansion valve. Refer to
HA-34, "LOW-PRESSURE FLEXIBLE HOSE : Removal and Installation"
and
HA-34, "HIGH-PRESSURE PIPE : Removal and Installation"
. (If equipped)
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve with suitable material such as vinyl
tape to avoid the entry of air.
JMIIA0752ZZ
1.
Packing
2.
Packing
3.
Ventilation unit case assembly
4.
Blower motor
5.
Cap
6.
EVAP dummy
7.
Patch
8.
Patch
9.
Heater pipe flange
10. Packing
11.
Front intake door case
12. Intake door
13. Rear intake door case
14.
Filter cover
15. Cap
16. Heater cover
17.
Foot door
18. Ventilator door
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст