Nissan March K13. Instruction — part 395
HAC-114
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONER]
COMPRESSOR DOSE DOT OPERATE
Check the blower fan ON signal. Refer to
HAC-108, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts
7.
CHECK THERMO CONTROL AMP.
Check the thermo control amp. Refer to
XX-XX, "*****"
.
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
XX-XX, "*****"
.
NO
>> Repair or replace the malfunctioning parts
A/C CONTROL
HAC-115
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REMOVAL AND INSTALLATION
A/C CONTROL
Exploded View
INFOID:0000000006024149
Removal and Installation
INFOID:0000000006024150
REMOVAL
1.
Remove A/C finisher. Refer to
IP-13, "Removal and Installation"
.
2.
Remove the air mix door cable from the A/C unit assembly. Refer to
HAC-120, "AIR MIX DOOR CABLE :
.
3.
Remove the mode door cable from the A/C unit assembly. Refer to
.
4.
Remove the intake door cable from the A/C unit assembly. Refer to
.
5.
Remove each door cable and harness connector the A/C control.
INSTALLATION
Install in the reverse order of removal.
1.
Mode door cable
2.
Illumination bulb
3.
Air mix door cable
4.
A/C control
5.
Intake door cable
6.
Intake door lever knob
7.
A/C control finisher
8.
Mode dial
9.
Temperature dial
10. Fan control dial
A.
To mode door link
B.
To air mix door link
C.
Intake door link
JMIIA0753ZZ
HAC-116
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONER]
THERMO CONTROL AMPLIFIER
THERMO CONTROL AMPLIFIER
Exploded View
INFOID:0000000006024151
.
Removal and Installation
INFOID:0000000006024152
REMOVAL
1.
Remove the evaporator. Refer to
HA-43, "EVAPORATOR : Removal and Installation"
2.
Remove the thermo control amp. from the evaporator.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
• When install the thermo control amp., set the same position before replacement.
• When remove the thermo control amp., never turn the bracket which is equipped the top of the
thermo control amp.
• Check for the leakages when recharging refrigerant. Refer to
REFRIGERANT PRESSURE SENSOR
HAC-117
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000006057678
.
Removal and Installation
INFOID:0000000006057679
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
22, "Perform Lubricant Return Operation"
REMOVAL
1.
Remove refrigerant pressure sensor. Refer to
HA-37, "REFRIGERANT PRESSURE SENSOR : Removal
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст