Nissan March K13. Instruction — part 314
EXL-82
< SYMPTOM DIAGNOSIS >
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000005912473
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000005912474
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
3.
PARKING LAMP CIRCUIT INSPECTION
Check the parking lamp circuit. Refer to
EXL-68, "Component Function Check"
.
Is the parking lamp circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-28, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
TAIL & CLR
REQ
Lighting switch
1ST
ON
OFF
OFF
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-83
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000005912475
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000005912476
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> GO TO 2.
2.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
(Without Intelligent Key).
Is the combination switch normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “FR FOG REQ” of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 4.
NO
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
(Without Intelligent Key).
4.
FRONT FOG LAMP RELAY CIRCUIT INSPECTION
Check the front fog lamp relay circuit. Refer to
Is the front fog lamp relay circuit normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning part.
5.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
EXL-66, "Component Function Check"
.
Is the front fog lamp circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#39
15 A
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
ON
OFF
OFF
EXL-84
< PERIODIC MAINTENANCE >
HEADLAMP AIMING ADJUSTMENT
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000006056700
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
• Headlamp aiming switch sets to “0”.
AIMING ADJUSTMENT SCREW
JMLIA1020ZZ
A.
Headlamp RH (UP/DOWN) adjust-
ment screw
B.
Headlamp RH (INSIDE/OUTSIDE)
adjustment screw
C.
Headlamp LH (INSIDE/OUTSIDE)
adjustment screw
D.
Headlamp LH (UP/DOWN) adjust-
ment screw
: Vehicle center
HEADLAMP AIMING ADJUSTMENT
EXL-85
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Aiming Adjustment Procedure
INFOID:0000000006056701
1.
Place the screen.
NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2.
Face the vehicle squarely toward the screen and make the distance between the headlamp bulb center
and the screen 10 m (32.8 ft).
3.
Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Never cover lens surface with tape, etc. because it is made from plastic.
4.
Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp RH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
B
Headlamp RH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
C
Headlamp LH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
D
Headlamp LH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
A.
Aiming adjustment area
B.
Elbow point
C.
Headlamp center
H.
Horizontal center line of headlamp
V.
Vertical center line of headlamp
JSLIA0028ZZ
JSLIA0029ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст