Nissan March K13. Instruction — part 601

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

SEC-143

< BASIC INSPECTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.

>> GO TO 2.

2.

REPLACE BCM

Replace BCM. Refer to

BCS-99, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT-III Configuration

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Instruction selection” to write
vehicle specification. Refer to

BCS-88, "Work Procedure"

.

>> GO TO 4.

4.

INITIALIZE BCM (NATS)

Perform BCM initialization. (NATS)

>> WORK END

SEC-144

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

P1610 LOCK MODE

DTC/CIRCUIT DIAGNOSIS

P1610 LOCK MODE

Description

INFOID:0000000006014777

ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times
or more while communication between ECM and BCM is not normal, or when engine start operation is per-
formed 5 times or more using the unregistered ignition key.

DTC Logic

INFOID:0000000006014778

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT-III.

Is DTC detected?

YES

>> Refer to

SEC-144, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006014779

1.

CHECK ENGINE START FUNCTION

1.

Perform the check for DTC except DTC P1610.

2.

Use CONSULT-III to erase DTC after fixing.

3.

Turn ignition switch OFF.

4.

Turn ignition switch ON using the registered ignition key and wait for 5 seconds.

5.

Turn the ignition switch OFF and wait 5 seconds.

6.

Repeat steps 4 and 5 twice (a total of 3 times).

7.

Check that engine can start using the registered ignition key.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1610

LOCK MODE

When ECM detects a communication malfunction between
ECM and BCM 5 times or more.

—

P1611 ID DISCORD, IMMU-ECM

SEC-145

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

P1611 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000006014781

DTC DETECTION LOGIC

NOTE:
• If DTC P1611 is displayed with DTC U1000 (for BCM), first perform the trouble diagnosis for DTC U1000.

Refer to

BCS-47, "DTC Logic"

.

• If DTC P1611 is displayed with DTC U1010 (for BCM), first perform the trouble diagnosis for DTC U1010.

Refer to

BCS-48, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT-III.

Is DTC detected?

YES

>> Refer to

SEC-145, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006014782

1.

PERFORM INITIALIZATION

Perform initialization of BCM and reregistration of all ignition keys using CONSULT-III.
For initialization and registration procedures, refer to CONSULT-III Operation Instruction NATS-IVIS/NVIS.

Can the system be initialized and can the engine be started with reregistered ignition key?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE BCM

1.

Replace BCM. Refer to

BCS-57, "Removal and Installation"

.

2.

Perform initialization of BCM and reregistration of all ignition keys using CONSULT-III.
For initialization and registration procedures, refer to CONSULT-III Operation Instruction NATS-IVIS/NVIS.

Can the system be initialized and can the engine be started with reregistered ignition key?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

REPLACE ECM

1.

Replace ECM. Refer to

EC-524, "Removal and Installation"

[HR12DE (TYPE 2)].

2.

Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”. Refer to

SEC-36, "ECM : Work Procedure"

[HR12DE (TYPE 2)].

3.

Start engine.

Does engine start?

YES

>> INSPECTION END

NO

>> GO TO 4.

4.

CHECK INTERMITTENT INCIDENT

Refer to

GI-33, "Intermittent Incident"

.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1611

ID DISCORD IMMU-ECM

The ID verification results between BCM
and ECM are NG.

• Harness or connectors

(The CAN communication line is open
or shorted.)

• BCM
• ECM

SEC-146

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

P1612 CHAIN OF ECM-IMMU

P1612 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000006014784

DTC DETECTION LOGIC

NOTE:
• If DTC P1612 is displayed with DTC U1000 (for BCM), first perform the trouble diagnosis for DTC U1000.

Refer to

BCS-47, "DTC Logic"

.

• If DTC P1612 is displayed with DTC U1010 (for BCM), first perform the trouble diagnosis for DTC U1010.

Refer to

BCS-48, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT-III.

Is DTC detected?

YES

>> Refer to

SEC-146, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006014785

1.

REPLACE BCM

1.

Replace BCM. Refer to

BCS-57, "Removal and Installation"

.

2.

Perform initialization of BCM and reregistration of all ignition keys using CONSULT-III.
For initialization and registration procedures, refer to CONSULT-III Operation Instruction NATS-IVIS/NVIS.

3.

Start engine.

Does the engine start?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

REPLACE ECM

1.

Replace ECM. Refer to

EC-524, "Removal and Installation"

[HR12DE (TYPE 2)].

2.

Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”. Refer to

SEC-36, "ECM : Work Procedure"

[HR12DE (TYPE 2)].

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1612

CHAIN OF ECM-IMMU

Inactive communication between ECM
and BCM

• Harness or connectors

(The CAN communication line is open or
shorted.)

• BCM
• ECM