Nissan March K13. Instruction — part 243
P0605 ECM
EC-433
< DTC/CIRCUIT DIAGNOSIS >
[HR12DE (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0605 ECM
DTC Logic
INFOID:0000000005886549
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1.
Turn ignition switch ON.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Turn ignition switch ON and wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Turn ignition switch ON and wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Repeat step 2 for 32 times.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005886550
1.
INSPECTION START
1.
Erase DTC.
2.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Is the 1st trip DTC P0605 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Perform
XX-XX, "*****"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
EC-434
< DTC/CIRCUIT DIAGNOSIS >
[HR12DE (TYPE 2)]
P0605 ECM
>> INSPECTION END
P1065 ECM
EC-435
< DTC/CIRCUIT DIAGNOSIS >
[HR12DE (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1065 ECM
DTC Logic
INFOID:0000000005886552
DTC DETECTION LOGIC
*: This self-diagnosis is not for ECM power supply circuit, even though “ECM BACK UP/CIRCUIT” is displayed on CONSULT-III screen.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON wait at least 10 seconds.
2.
Turn ignition switch OFF and wait at least 5 minutes
3.
Turn ignition switch ON, wait at least 10 seconds.
4.
Repeat step 2 and 3 for five times.
5.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005886553
1.
INSPECTION START
1.
Erase DTC.
2.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Is the 1st trip DTC P1065 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Perform
XX-XX, "*****"
.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1065
*
Engine control module
ECM back-up RAM system does not function
properly.
• ECM
EC-436
< DTC/CIRCUIT DIAGNOSIS >
[HR12DE (TYPE 2)]
P1121 ELECTRIC THROTTLE CONTROL ACTUATOR
P1121 ELECTRIC THROTTLE CONTROL ACTUATOR
DTC Logic
INFOID:0000000005886557
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B
1.
Turn ignition switch ON and wait at least 1 second.
2.
Set shift lever to D position (A/T) or 1st position (M/T) position and wait at least 3 seconds.
3.
Set shift lever to P position (A/T) or Neutral position (M/T).
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Turn ignition switch ON and wait at least 1 second.
6.
Set shift lever to D position (A/T) or 1st position (M/T) position and wait at least 3 seconds.
7.
Set shift lever to P position (A/T) or Neutral position (M/T).
8.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
9.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Turn ignition switch ON and wait at least 1 second.
2.
Set shift lever to D position (A/T) or 1st position (M/T) position and wait at least 3 seconds.
3.
Set shift lever to P position (A/T) or Neutral position (M/T).
4.
Start engine and let it idle for 3 seconds.
5.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005886558
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Turn ignition switch OFF.
2.
Remove the intake air duct.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1121
Electric throttle control
actuator
A)
Electric throttle control actuator does not function
properly due to the return spring malfunction.
• Electric throttle control actuator
B)
Throttle valve opening angle in fail-safe mode is
not in specified range.
C)
ECM detect the throttle valve is stuck open.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст