Nissan March K13. Instruction — part 455
MA-26
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
DRIVE SHAFT : Inspection
INFOID:0000000005943137
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SFA108A
BODY MAINTENANCE
MA-27
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000005943138
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000005943139
For front seat belt illustration. Refer to
XX-XX, "*****"
.
For rear seat belt illustration. Refer to
XX-XX, "*****"
.
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
XX-XX, "*****"
,
XX-XX, "*****"
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
BODY CORROSION
BODY CORROSION : Checking Body Corrosion
INFOID:0000000005943140
Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.
HEMMED PANELS
Hood front end, door lower end, trunk lid rear end, etc.
PANEL JOINT
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine com-
partment, etc.
PANEL EDGE
Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
PARTS CONTACT
Waist moulding, windshield moulding, bumper, etc.
PART
WITH INTELLIGENT KEY SYSTEM
WITHOUT INTELLIGENT KEY SYSTEM
Hood
Refer to
Refer to
XX-XX, "*****"
.
Hood lock
Refer to
Refer to
XX-XX, "*****"
.
Front door
Refer to
Refer to
XX-XX, "*****"
.
Front door lock
Refer to
Refer to
XX-XX, "*****"
.
Rear door
Refer to
Refer to
XX-XX, "*****"
.
Rear door lock
Refer to
Refer to
XX-XX, "*****"
.
Back door
Refer to
Refer to
XX-XX, "*****"
.
Back door lock
Refer to
Refer to
XX-XX, "*****"
.
MA-28
< PERIODIC MAINTENANCE >
BODY MAINTENANCE
PROTECTORS
Damage or condition of mudguard, fender protector, chipping protector, etc.
ANTI-CORROSION MATERIALS
Damage or separation of anti-corrosion materials under the body.
DRAIN HOLES
Condition of drain holes at door and side sill. When repairing corroded areas, refer to the Corrosion Repair
Instruction.
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-29
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELT
DRIVE BELT : Drive Belt
INFOID:0000000006069235
DRIVE BELT
Belt Deflection
*: When engine is cold.
Belt Tension and Frequency
*: When engine is cold.
ENGINE COOLANT
ENGINE COOLANT : Periodical Maintenance Specification
INFOID:0000000006069238
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, Imp qt)
ENGINE OIL
ENGINE OIL : Periodical Maintenance Specification
INFOID:0000000006069237
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
SPARK PLUG
SPARK PLUG : Spark Plug
INFOID:0000000006069236
SPARK PLUG (PLATINUM-TIPPED TYPE)
Location
Deflection adjustment *
Unit: mm (in)
Used belt
New belt
Limit
After adjusted
Drive belt
With A/C
10.9 (0.32)
5.1 - 5.6 (0.19 - 0.21)
4.3 - 4.7 (0.16 - 0.17)
Without A/C
9.8
4.6 - 5.0
3.9 - 4.2
Applied pushing force
98 N (10 kg, 22 lb)
Location
Tension adjustment *
Unit: N (kg, lb)
Frequency adjustment *
Unit: Hz
Used belt
New belt
Used belt
New belt
Limit
After adjusted
Limit
After adjusted
Drive belt
330 (51.0, 112)
876 - 964
(89.4 - 98.3,
197 - 217)
1064 - 1152
(108.5 - 117.5,
239 - 259)
133
217 - 227
239 - 248
Engine coolant capacity (With reservoir tank at “MAX” level)
A/T models
5.5 (5-6/8, 4-7/8)
M/T models (without EGR control
valve)
M/T models (with EGR control valve)
5.7 (6, 5)
Reservoir tank engine coolant capacity (At “MAX” level)
0.7 (3/4, 5/8)
Drain and refill
With oil filter change
3.0 (3-1/8, 2-5/8)
Without oil filter change
2.8 (3, 2-4/8)
Dry engine (Overhaul)
3.5 (3-6/8, 3-1/8)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст