Nissan March K13. Instruction — part 128
FRONT DOOR
DLK-223
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform the fitting adjustment. Refer to
DLK-223, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR ASSEMBLY : Adjustment
INFOID:0000000006067035
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove fender protector. Refer to
EXT-17, "FENDER PROTECTOR : Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
Refer to
Portion
Clearance
Surface height
Front fender – Front door
A – A
3.7 – 5.7 (0.146 – 0.224)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
B – B
3.7 – 5.7 (0.146 – 0.224)
- 1.0 – 1.0 (- 0.039 – 0.039)
JMKIA5318GB
DLK-224
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
8.
Install front fender protector. Refer to refer to
EXT-17, "FENDER PROTECTOR : Removal and Installa-
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000006067036
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000006067037
REMOVAL
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove fender protector. Refer to
EXT-17, "FENDER PROTECTOR : Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-222, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-223, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000006067038
REMOVAL
1.
Fully close the front door window.
2.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
3.
Remove sealing screen (lower). (Without door speaker)
FRONT DOOR
DLK-225
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Remove front door speaker mounting bolts.
5.
Disconnect connector and remove front door speaker.
6.
Remove mounting bolts of door check link on the vehicle.
7.
Remove mounting bolts of door check link on door panel.
8.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check front door open/close operation after installation.
DLK-226
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
Exploded View
INFOID:0000000006067039
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000006067040
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door harness grommet, and then pull out door harness from the vehicle.
2.
Disconnect rear door harness connector.
3.
Remove mounting bolts of door check link on the vehicle.
4.
Remove door hinge mounting nuts (door side), and then remove rear door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check rear door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-227, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Rear door panel
2.
Door hinge (upper)
3.
Door hinge (lower)
4.
Door check link
5.
Sealing screen (lower)
6.
Bumper rubber
7.
Door striker
8.
TORX bolt
9.
Grommet
Refer to
for symbols in the figure.
JMKIA5319GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст