Nissan March K13. Instruction — part 435
LAN-28
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
MALFUNCTION AREA CHART
DTC/CIRCUIT DIAGNOSIS
MALFUNCTION AREA CHART
Main Line
INFOID:0000000005908821
Branch Line
INFOID:0000000005908822
Short Circuit
INFOID:0000000005908823
Malfunction area
Reference
Main line between IPDM E/R and data link connector
Malfunction area
Reference
ECM branch line circuit
ABS actuator and electric unit (control unit) branch line circuit
IPDM E/R branch line circuit
TCM branch line circuit
Data link connector branch line circuit
EPS control unit branch line circuit
Combination meter branch line circuit
BCM branch line circuit
Malfunction area
Reference
CAN communication circuit
LAN
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
LAN-29
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000005908847
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the following harness connectors.
-
IPDM E/R
-
Harness connectors E105 and M77
2.
Check the continuity between the IPDM E/R harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the IPDM E/R and the harness connector E105.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
Check the continuity between the harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the IPDM E/R and the data link connector.
NO
>> Repair the main line between the harness connector M77 and the data link connector.
IPDM E/R harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E10
12
E105
80
Existed
11
81
Existed
Harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M77
80
M4
6
Existed
81
14
Existed
LAN-30
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
ECM BRANCH LINE CIRCUIT
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000005908848
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the ECM for damage, bend and loose connection (unit side and
connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of ECM.
2.
Check the resistance between the ECM harness connector terminals.
-
With D-Jetronic engine
-
With L-Jetronic engine
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to the following.
NOTE:
Check the vehicle type to confirm the service information. Refer to
EC-9, "How to Check Vehicle Type"
• HR12DE (TYPE 1):
• HR12DE (TYPE 2):
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to the following.
• HR12DE (TYPE 1):
• HR12DE (TYPE 2):
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E16
52
51
Approx. 108 – 132
ECM harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E18
84
83
Approx. 108 – 132
LAN
ABS BRANCH LINE CIRCUIT
LAN-31
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ABS BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000005908849
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the ABS actuator and electric unit (control unit) for damage, bend
and loose connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of ABS actuator and electric unit (control unit).
2.
Check the resistance between the ABS actuator and electric unit (control unit) harness connector termi-
nals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ABS actuator and electric unit (control unit) branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ABS actuator and electric unit (control unit). Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the ABS actuator and electric unit (control unit).
YES (Past error)>>Error was detected in the ABS actuator and electric unit (control unit) branch line.
NO
>> Repair the power supply and the ground circuit.
ABS actuator and electric unit (control unit) harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E34
26
14
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст