Nissan March K13. Instruction — part 553
REAR WHEEL HUB
RAX-7
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
• Check snap ring for wear or cracks. Replace if necessary.
INSPECTION AFTER ASSEMBLY
1.
After installing brake drum on spindle, tighten wheel hub lock nut to the standard torque.
2.
Rotate the wheel hub in both directions ten times each to check for smooth movement.
3.
Rotating speed of 8 – 10 rpm, place a spring balance on hub bolt
to measure torque.
INSPECTION AFTER INSTALLATION
1.
Adjust parking brake operation (stroke). Refer to
XX-XX, "*****"
.
2.
Check wheel alignment. Refer to
XX-XX, "*****"
.
Rotating torque
.
Spring balance
measurement
.
MDIA0060E
RAX-8
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000006044170
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Rotating torque
0.20 - 0.95 N·m (0.02 - 0.09 kg-m)
Spring balance measurement
4 - 19 N (0.41 - 1.94 kg)
RSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
RSU
A
B
RSU
N
O
P
CONTENTS
REAR SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Suspension . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR SUSPENSION ASSEMBLY . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR SHOCK ABSORBER . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ....
COIL SPRING . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
REAR SUSPENSION BEAM . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
RSU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Suspension
INFOID:0000000006044850
• When installing rubber bushings, the final tightening must be carried out under unladen conditions with tires
on ground. Spilled oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
• After servicing suspension parts, be sure to check wheel alignment.
• Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are pre-oiled,
tighten as they are.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст