Nissan March K13. Instruction — part 670
ROAD WHEEL
WT-3
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PERIODIC MAINTENANCE
ROAD WHEEL
Tire rotation
INFOID:0000000006043983
• Follow the maintenance schedule for tire rotation service intervals.
Refer to
XX-XX, "*****"
.
• When installing the wheel, tighten wheel nuts to the specified
torque.
CAUTION:
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
Wheel nuts tighting torque
: Refer to
.
SMA829C
WT-4
< REMOVAL AND INSTALLATION >
ROAD WHEEL TIRE ASSEMBLY
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000006043984
Removal and Installation
INFOID:0000000006043985
REMOVAL
1.
Remove wheel nuts.
2.
Remove tire assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000006043986
ALUMINUM WHEEL
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
If the lateral deflection (A) or vertical deflection (B) for radial
runout value exceeds the limit, replace aluminum wheel.
STEEL WHEEL
1.
Check tires for were and improper inflation.
1.
Tire assembly
Refer to
XX-XX, "*****"
for symbols in the figure.
JSGIA0640GB
Limit
A:
.
B:
.
SEIA0737E
ROAD WHEEL TIRE ASSEMBLY
WT-5
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
2.
Check wheels for deformation, clacks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from steel wheel and mount wheel on a tire balance machine.
b.
Set two dial indicators as shown in the illustration.
c.
Set each dial indicator to “0”.
d.
Rotate wheel and check dial indicators at several points around
the circumference of the wheel.
e.
Calculate runout at each point as shown below.
f.
Select maximum positive runout value and the maximum nega-
tive value. Add the two values to determine total runout.
CAUTION:
In case a positive or negative value is not available, use the
maximum value (negative or positive) for total runout.
g.
If the total runout value exceeds limit, replace steel wheel.
Lateral runout limit (A):
(
+
)/2
Radial runout limit (B):
(
+
)/2
Limit
A:
Refer to
B:
Refer to
SEIA0738E
WT-6
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000006043987
ALUMINUM WHEEL
STEEL WHEEL
STEEL WHEEL (FOR EMERGENCY USE)
Tire Air Pressure
INFOID:0000000006043988
Unit: kPa (bar, kg/cm
2
, psi)
Item
Limit
Radial runout
Lateral deflection
Less than 0.3 mm (0.012 in)
Vertical deflection
Allowable unbalance
Dynamic (At flange)
Less than 10 g (0.35 oz) (one side)
Static (At flange)
Less than 20 g (0.70 oz)
Item
Limit
Radial runout
Lateral deflection
Less than 0.8 mm (0.031 in)
Vertical deflection
Less than 0.5 mm (0.020 in)
Allowable unbalance
Dynamic (At flange)
Less than 10 g (0.35 oz) (one side)
Static (At flange)
Less than 20 g (0.70 oz)
Item
Limit
Radial runout
Lateral deflection
Less than 0.8 mm (0.031 in)
Vertical deflection
Less than 0.5 mm (0.020 in)
Allowable unbalance
Dynamic (At flange)
Less than 10 g (0.35 oz) (one side)
Static (At flange)
Less than 20 g (0.70 oz)
Tire size
Air pressure
Front
Rear
Half load
Maximum load
165/70R14 81S
220 (2.2, 2.2, 32)
220 (2.2, 2.2, 32)
300 (3.0, 3.0, 44)
175/60R15 81H
220 (2.2, 2.2, 32)
220 (2.2, 2.2, 32)
300 (3.0, 3.0, 44)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст