Nissan March K13. Instruction — part 584
B2604 SHIFT POSITION
SEC-75
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NO
>> Replace transaxle assembly. Refer to TM.
7.
CHECK INTERMITTENT INCIDENT
GI-33, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006044293
1.
CHECK TRANSMISSION RANGE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to TM.
Transmission range switch
Condition
Continuity
Terminal
7
10
P or N position
Existed
Other than above
Not existed
SEC-76
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2605 SHIFT POSITION
B2605 SHIFT POSITION
DTC Logic
INFOID:0000000006038547
DTC DETECTION LOGIC
NOTE:
• If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2605 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift the selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift the selector lever to the N position and wait 1 second or more.
4.
Shift the selector lever to other than the P and N positions and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006038548
1.
CHECK IPDM E/R INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Turn ignition switch ON.
4.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-28, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK IPDM E/R INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between IPDM E/R harness connector and BCM harness connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2605
PNP/CLUTCH SW
When ignition switch is ON, P/N position
signal input from transmission range switch
and P/N position signal (CAN) input from
IPDM E/R do not match.
• Harness or connectors
(The CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
F115
76
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
B2605 SHIFT POSITION
SEC-77
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
NO
>> Repair or replace harness.
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
F115
76
M71
102
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
F115
76
Not existed
SEC-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC Logic
INFOID:0000000006038549
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions to start engine.
-
Selector lever: In the P position
-
Brake pedal: Depressed
2.
Wait 1 second after engine started.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006038550
1.
CHECK DTC WITH IPDM E/R
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK STARTER RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect starter relay.
3.
Disconnect BCM connector connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM outputs starter motor relay OFF signal
but BCM receives starter motor relay ON
signal from IPDM E/R (CAN).
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
• Starter relay
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M71
97
Ground
Selector lever
N or P position
Battery voltage
Other than above
0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст