Nissan March K13. Instruction — part 275
EM-34
< REMOVAL AND INSTALLATION >
[HR12DE]
OIL PAN (LOWER)
OIL PAN (LOWER)
Exploded View
INFOID:0000000005988184
Removal and Installation
INFOID:0000000005988185
REMOVAL
1.
Drain engine oil. Refer to
.
2.
Remove oil pan (lower) with the following procedure:
1.
Rear oil seal
2.
O-ring
3.
Oil pan (upper)
4.
Oil pump chain tensioner
5.
Oil pump drive chain
6.
Crankshaft sprocket
7.
Oil pump sprocket
8.
Oil pump
9.
O-ring
10. Drain plug
11.
Drain plug washer
12. Oil pan (lower)
13. Oil filter
A.
B.
Oil pan (lower) side
Refer to
for symbols in the figure.
JPBIA3384GB
OIL PAN (LOWER)
EM-35
< REMOVAL AND INSTALLATION >
[HR12DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen mounting bolts in reverse order as shown in the figure.
b.
Insert seal cutter [SST: KV10111100] (A) between oil pan (upper)
and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• Never insert a screwdriver. This damages the mating sur-
faces.
c.
Slide the seal cutter [SST: KV10111100] by tapping on the side
of tool with a hammer.
d.
Remove oil pan (lower).
INSTALLATION
1.
Install oil pan (lower) as follows:
a.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surface when cleaning
off old liquid gasket.
: Engine front
JPBIA3378ZZ
JPBIA0276ZZ
PBIC3953E
EM-36
< REMOVAL AND INSTALLATION >
[HR12DE]
OIL PAN (LOWER)
b.
Apply a continuous bead of liquid gasket (B) with a tube presser
(commercial service tool) as shown in the figure.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
c.
Tighten bolts in numerical order as shown in the figure.
2.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
.
3.
Install in the reverse order of removal after this step.
NOTE:
Wait at last 30 minutes after oil pan (lower) is installed before pouring engine oil.
Inspection
INFOID:0000000005988186
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leakage of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
a
: 7.5 - 9.5 mm (0.295 - 0.374 in)
c
:
φ
4.0 - 5.0 mm (0.157 - 0.197 in)
1
: Oil pan (lower)
: Engine outside
JPBIA3379ZZ
: Engine front
JPBIA3378ZZ
FUEL INJECTOR AND FUEL TUBE
EM-37
< REMOVAL AND INSTALLATION >
[HR12DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000005988187
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
Removal and Installation
INFOID:0000000005988188
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
REMOVAL
1.
Release the fuel pressure. Refer to folloeing;
• HR12DE (TYPE 1):
• HR12DE (TYPE 2):
2.
Disconnect battery cable from negative terminal.
3.
Remove air duct (inlet) and air cleaner assembly. Refer to
EM-24, "Removal and Installation"
.
4.
Remove intake manifold. Refer to
EM-28, "WITHOUT EGR CONTROL VALVE : Removal and Installation"
(Without EGR control valve) or
EM-30, "WITH EGR CONTROL VALVE : Removal and Installation"
(With
EGR control valve).
5.
Disconnect quick connector with the following procedure.
a.
Remove fuel feed tube protector.
1.
Clamp
2.
Bracket
3.
Fuel feed tube
4.
Fuel tube protector
5.
Quick connector cap
6.
Fuel pipe
7.
Fuel tube
8.
O-ring (black)
9.
Fuel injector
10. Clip
11. O-ring (green)
Refer to
for symbols in the figure.
JPBIA3388GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст