Nissan March K13. Instruction — part 116
KEYFOB ID REGISTRATION
DLK-175
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID REGISTRATION
Description
INFOID:0000000006038733
Perform the following procedure after BCM is replaced or when new keyfob ID is registered
NOTE:
When registering the keyfob ID, perform only one procedure to simultaneously register both ID (IMMOBI-
LIZER ID and keyfob ID).
Work Procedure
INFOID:0000000006038734
1.
STEP 1
Close all doors.
>> GO TO 2.
2.
STEP 2
Perform lock operation by door lock/unlock switch or driver door lock knob.
>> GO TO 3.
3.
STEP 3
1.
Remove and insert the key into the ignition key 6 times within 10seconds (turning
the key switch from OFF to ON counts as 1 time).
2.
All doors unlock automatically.
NOTE:
On the sixth key insertion, keep the key in the cylinder with the key switch ON.
Do all doors unlock automatically?
YES
>> GO TO 4.
NO
>> GO TO 1.
4.
STEP 4
Turn ignition switch to ACC within 3 seconds after all doors unlock and perform lock operation by door lock/
unlock switch or driver door lock knob.
>> GO TO 5.
5.
STEP 5
1.
Press the lock or unlock button of the keyfob to be added.
2.
All doors unlock simultaneously.
3.
Key ID is registered.
Is key ID registered?
YES-1 >> When adding a keyfob: GO TO 6.
YES-2 >> When ending registration: GO TO 8.
NO
>> GO TO 1.
6.
STEP 6
Perform lock operation by door lock/unlock switch or driver door lock knob.
>> GO TO 5.
7.
STEP 7
1.
Press the lock or unlock button of the keyfob to be added.
2.
All doors unlock simultaneously.
3.
Key ID is registered.
Is key ID registered?
YES-1 >> When adding a keyfob: GO TO 6.
DLK-176
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID REGISTRATION
YES-2 >> When ending registration: GO TO 8.
NO
>> GO TO 6.
8.
STEP 8
Open any door.
>> REGISTRATION END
DOOR SWITCH
DLK-177
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DTC/CIRCUIT DIAGNOSIS
DOOR SWITCH
Component Function Check
INFOID:0000000006068636
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL”, “DOOR SW-RR” and “BACK DOOR SW” in
“DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-177, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006068637
1.
CHECK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning door switch connector.
3.
Check signal between malfunctioning door switch harness connector and ground using oscilloscope.
Monitor item
Condition
Status
DOOR SW-DR
Driver side door
Open
ON
Closed
OFF
DOOR SW-AS
Passenger side door
Open
ON
Closed
OFF
DOOR SW-RL
Rear door LH
Open
ON
Closed
OFF
DOOR SW-RR
Rear door RH
Open
ON
Closed
OFF
BACK DOOR SW
Back door
Open
ON
Closed
OFF
DLK-178
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR SWITCH
(+)
(–)
Condition
Signal
(Reference value)
Door switch
Connector
Terminal
Driver side
B35
3
Ground
Driver door
switch
OFF (When
driver door
closed)
7.0 - 8.0 V
ON (When driv-
er door
opened)
0 V
Passenger
side
B28
3
Passenger
door switch
OFF (When
passenger door
closed)
7.0 - 8.0 V
ON (When pas-
senger door
opened)
0 V
Rear LH
B71
3
Rear LH door
switch
OFF (When
rear LH door
closed)
7.0 - 8.0 V
ON (When rear
door LH
opened)
0 V
Rear RH
B53
3
Rear RH door
switch
OFF (When
rear RH door
closed)
7.0 - 8.0 V
ON (When rear
RH door
opened)
0 V
PKIB4960J
PKIB4960J
PKIB4960J
PKIB4960J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст